redcat rc 3d models

Redcat Gen7 54mm bump mount reinforced and extended

Trx-4 to Redcat Everest Gen7 Bumper Mount

Spur Gear RedCat Truck - Volcano EPX 1/10 56T

Traxxas Trx-4 Front Bumper made to fit Redcat Everest Gen 7 Pro

Front Grill for Redcat Everest Gen7 .The diameter of the applicable headlight is 14mm

Trx-4 to Redcat Everest Gen8 V2 Bumper Mount works with front or back

Redcat Everest Gen 7 enthusiast mods every last component themselves to unlock hidden performance potential.

This design fits over the commonly available RC 540/550 sized heatsink with dual 30mm fans. It should fit any dual 30mm fan setup, so long as the fans are seated side-by-side. I am using this in my Redcat Racing Blackout XTE (converted to XBE) with...

A quick part I designed for the Redcat Shredder V2 1/6 scale RC truck while waiting for a replacement to arrive. I uploaded two versions: one with 25T teeth like the stock part and one with no teeth. I had trouble printing the 25T teeth on FDM. On my...

A simple snap-on bracket lets you quickly install or remove the Sense ESS One 2017 sound module from a Redcat Gen7 Crawler with ease.

This was a quick model I made for my Redcat Gen 7 when I upgraded to the Flysky GT5 and needed to mount the receiver. ...

I had an amazing time trying out this snorkel system! I managed to clean and use an inline foam block that came in a box, which worked perfectly with the weedeater type filter. However, I found it easier to attach just the stock air filter unit to...

The objective is constructing a mechanism that changes the vertical suspension into a horizontal one. It functions through employing planes set at a 45-degree angle, which transfers energy via a pivot to the center of the R/C car. ...Further parts will...

Headlight upgrade kit that adds a burst of personality to your Gen8 vehicle. ...Compatible with 23mm googly eyes for an extra dash of charm.

Print horizontal lines with reinforced backing to ensure stability. ...Seal the finished project with vibrant, high-gloss 2K epoxy adhesive designed specifically for use with 3mm LED components.

three part roof protector

Shipping has been horrible lately and I need to get back on the trail. I whipped this up on tinkercad to get me rolling again. I am not a professional by any means. It works and that all I cared about. ...Happy Trails.

This is a remix of the print from ohioorbs.I found the walls on that version were too high to allow for the stock frame brace.The mounting holes also didn't line up on my truck.So I created this remix with shorter walls and revised mounting holes.It...

smaller light weight battery tray.fits max 2200 size packsmounts in stock location. ...stock hardware will work

RedcatGen7 Skid plate Features: +Very smooth belly, allow sliding on obstacles. +Fits perfet to the Stock Gear. +Rigid design. +Access to the Driveshaft set screwes without disassemble the skid plate. ... Hardwere Required: Type ...

To upgrade your setup, you'll need to install a 30mm fan directly into the suspension tower at the front, and then carefully slice through the bodywork. ...This allows the provided hood scoops to seamlessly slide on top of the fan, protruding from the...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Printable Diff case, may need slight sanding due to printer tolerances.

Because I can't own something without messing with it... often even before using it... I swapped out the radio gear on my fs-gt3b and now I need to switch to a 3s 5000. So, I jumped into CAD tonight (it arrived tonight) and measured everything out,...

Shouldnt have any problems printing. ...might need some slight sanding.

We misplaced our battery holder and I designed a new one with each of my kids' names engraved in the center. I uploaded an additional version without any name in the middle. ... Compatible with: Blackout SC, Blackout SC Pro, Blackout xbe, Blackout xbe...

This is a hitch I created to fit the Redact Racing Gen8 and Gen8 V2. I could not find any hitches to buy online and the ones I 3d printed did not come out so nice. I have not printed this part yet so if there is anything wrong, feel free to tell me.

I decided to create new bumper supports for my blackout without purchasing them. I figured it would be easier that way. ... Print Settings Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: .2500mm Infill: 100%

So I spent 2 hours measuring the redact volcano and designing this body and tweaking but I never printed it and I'm kind of sad about that . ...but I'm 90% it will work I just don't want to use a whole roll of filament to make it