reloading die 3d models

Wrench with handle for reloading die lock nuts. ... Tested on RCBS dies.

This is a Reloading Die Wrench for both standard nut size and Lee Dies.

A Stand For Reloading Dies That's Easy To Use. ... Reloaders Love This Stand Because It Doesn't Need Any Instructions.

A simple wall mounted rack to hold extra reloading die nuts. ... See more details and get the design files at https://azjake.com/die-nut-holder

Box to keep reloaded dies organized, adapts to all calibers since the diameter and general measurements of the reloading dies for short arms are similar in length and same diameter. Design developed for www.recargadoresargentinos.com.ar/foro forum...

Reloading Die Storage for Easy Access with the Hornady Lock-N-Load Bushing System The Hornady Lock-N-Load Bushing system makes it easy to store and reload your dies, allowing you to quickly swap them out when needed. This convenient storage solution...

Counter nut to prevent reloading die nuts from loosening whilst screwing the die in or out. Especially useful if you wish to keep the Lee nut with rubber O-ring, which prevents loosening of the die during use. Might need some scaling (101-102%)...

A 6 space die block that fits any standard reloading die. The block is blank and doesn't have any calibers listed on it like in the photo. ... Edit: I added a revised and refined die block under "die block revised"

This wrench is a remix the Reloading Die Wrench by itsnevergoingtowork. Instead of the Lee Die Lock rings, I created this for the RCBS sizing lock ring and the Hornaday Sure-Loc rings. I removed the concave handle as I do not think it printed...

These are reloading die holders to mount your dies to the wall or pegboard. Three of them fit the standard 7/8" dies and the other three fit dies with the Hornady Lock-N-Load mounted on the die. Each one has a place for a label and a stem for...

These are reloading die holders to mount your dies to the wall or pegboard. Three of them fit the standard 7/8" dies and the other three fit dies with the Hornady Lock-N-Load mounted on the die. Each one has a place for a label and a stem for...

A simple wall mounted rack to hold extra reloading die nuts. ...See more details and get the design files at https://azjake.com/die-nut-holder Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: .16 Infill: ...

A wall mount to hold reloading dies with the shell holder.Available for screw in or Multiboard.  The screw-in style uses M4 screws.  The Multiboard style uses Dual Snap Connector - Part B.  It will hold the die weight on the Mutlboard as is but I...

Reloading Die Locking Ring by Olin Coles Fits most 7/8"-14 threaded dies made by Lee, Hornady, RCBS, Forster, and Redding. This affordable alternative to metal versions sold retail is a 3D-printed solution. More reloading tools: Lee Case Trimmer...

I modified [Lorenzo Gonzalez's](https://www.thingiverse.com/lorenzogonzalez/designs) lovely [Reloading Die Organizer](https://www.thingiverse.com/thing:2216403) to work better with my pegboard, plus a couple other minor improvements: * Changed the...

The is a prototype of a wrench used to tighten/loosen the nut on reloading dies.  Fits a 1-1/8" nut.  This was designed for Lee reloading presses which have a very tight area to fit the wrench.  Now that the prototype works/fits I will...

Reloading die lock ring. Works for all dies with standard 7/8"-14 thread. I'm using these in Lee dies and RCBS dies with damaged brass set screws. Print vertically with supports turned on so the thread comes out well, I used 15% ZigZag. Remove...

This is a box for reloading dies. If you're like me (let's just pretend for a moment) you probably have a lot of dies rattling around in cardboard boxes. Maybe the original box was damaged. Maybe you got it used and there was no original box. Or...

Created a Lee Die Spanner for tightening of Lee dies. ...

Loading the die holder into position on a typical wooden rack is straightforward and effortless.

... plate, let me know and I'll add it. Versions: 3-Die Holder - No Nameplate 3-Die Holder - Blank 3-Die Holder - 7.62x39 3-Die Holder - 300 BLK 3-Die Holder - 9mm Luger 3-Die Holder - 10mm/40S&W Added: 3-Die Holder - Blank nameplate w/ Shell Holders

The standard-duty die block is designed to hold dies with 7/8"-14 threads. ...It's suitable for the majority of manufacturers such as RCBS, Lyman, Dillon, LEE, and Redding, among others.

Single die shelves and 3-die shelves are available. If demand is sufficient, I will add a 4-die version. The shelves are designed to hold dies equipped with the Lee bushing (or equivalent). I have tested them with Lee and RCBS dies, and everything...

This is my take on a die holder I only have the three die sets so I didn't want to have one with extra holes this has a shell plate holder and a measuring spoon holder. ...I can make other versions but I included the blank plate if you'd like to make...

I needed a simple way to store my often-used decapping die within easy reach. ...This mounting system securely attaches the die to the edge of my workbench, keeping it out of the way yet still accessible. ...It was effortless to print.

Originally designed to accommodate dies in Hornady LnL bushings, this rack can be scaled down to fit standard dies - an 80% reduction seems feasible, although further confirmation is needed. To secure the rack, I'm using a couple of small bolts...

... Pretty obvious.. You can replace my Dillon Powder Die Box (https://www.thingiverse.com/thing:5393613) with this one set to: numDies=1 dieLength=78.5; ringThickness=9; ringBottom=3; ringSide=4; ringOffset=29 and set the text how you like. ...

Reloading die box for 3 die set

A box I printed to hold a set of rifle reloading dies and shellholder for a set that came without a box.

Reloading die organizer that holds up to 8 dies. ...Will fit on an Ender 5 Plus