replacement nalgene lid 3d models

American car owners seeking a secure storage solution for their hydration needs will appreciate this 2019 Toyota Tacoma accessory designed specifically to hold Nalgene water bottles and similar sizes.

Insert for Tesla Model 3 center console cup holder to hold a 32 oz Nalgene bottle. This model is carefully designed with a subtle taper from the bottom to the top, ensuring a precise fit inside the cup holder. The Nalgene bottle fits snugly but not...

I created this Nalgene Water Bottle cap to convert a typical Nalgene "Wide Mouth" 32 oz. bottle into a watering can for my house plants. Print the cap upside down (open end up) and the nozzle with the small end up, no supports are needed. I...

The issue without using this adapter is the radius of the bottle holder is too small for the size of the nalgene bottle so it puts some flex into the fidlock holder that is not good. This adapter fills in the gap. I have seen my bottle slip...

This is an adapter to size up the cupholder on a Toro riding mower to fit a Nalgene 32 oz water bottle. ... Note: Does not seem to work in most car cupholders unless the cupholder is very small - the center of gravity is too high.

I present to you the mighty cupholder for those long road trips.It is easy to print and even more easy to install.The cupholder hold Nalgene bottles with 92mm diameter, the 1 liter version and the great 1.5 liter model.It's designed for a Volkswagen...

This cupholder expander accomodates a Nalgene-sized water bottle (up to 3.6") in smaller more standard cupholders in cars (3"). This in particular was made to fit in the 2020 Subaru Forester, but it should work in many cars. ... Should be printable...

made specifically for the '21 Kona EV front cup holder, but it fits both & probably some other vehicles. ...Used PETG,sans-supports. Nalgene seats better upside-down but works both ways. ...may modify further to follow the slope of the console...

Glue Collar to Inside Lip of the Nalgene Bottle (Super Glue or Hot Glue) 4. Hot Glue Combo Lock to Center of the Inside of the Cap 5. Add Colored Stripe in Three Spots of the Combo (This Will Be Reference Line) 6. Starting at Notch in the Collar,...

I found the clearance of the remixed Nalgene narrow mouth strap a tad too tight for my case. This remix changes: - Parametric additional clearance for both openings (set to +1mm diameter) - larger fillet for added stability (I carry the full...

I'm getting frustrated with all the people at my gym using the same Nalgene bottle - so I've decided to take matters into my own hands and design a ring that can detect my everyday OTF bottle. Update 2017-11-07: A customizer is now available for...

They also don't offer a product for the 32oz narrow-mouth Nalgene. I made this to fill the gap! It screws onto the neck, and the bottle cap holds it firmly in place when closed. I used paracord to make the strap. I made this utilizing Auburn's...

I Accidentally Broke My Nalgene Bottle Holder, But It Still Works After Fixing It. Here's How I Made It Fit into My Chevy Astro Cupholder Using Electrical Tape. Print Settings: Supports: No Notes: To print the holder perfectly, make sure to use a...

1 liter Nalgene water bottle mount for the Hi-hat stand. Measure your cymbal hardware and adjust the mounting hole size as needed. You could use tape or teflon tape to snug the fit to stop the water bottle from sliding down. ...I heat the hi-hat stand...

My dad wanted a water bottle holder for his exercise machine that could hold his 1L Nalgene bottle (92 mm diameter).&nbsp;It is held in place with 4 M5 bolts and nuts. You can put the nuts into the recess in the top part.&nbsp;</p><p>It is bolted...

Nalgene bottle. The model is slightly tapered from the bottom to the top to fit snugly inside the cup holder and the Nalgene bottle is a snug (but not tight) fit. The bottom of the holder is open to save filament and to not create a suction or trap...

lid

Most vehicle cupholders don't fit Nalgenes or Hydroflasks, so here's an adaptor to fix it! Designed to perfectly fit into the the cupholder for a 2019 Honda CR-V. After printing, apply strips of felt around the outside walls of the part that is...

Transform your office desk into a fun zone with this unique and intriguing toy made from a 32oz Nalgene bottle. Simply follow these easy steps: cut the threads of the black cap to allow it to spin freely, glue a collar inside the lip of the bottle...

This device serves as a protective cover for Nalgene water bottles, securing the bottle cap and preventing it from accidentally opening within one's backpack if not secured properly. I recently utilized this product during my visit to Sequoia and...

That's why I invested in this adapter, which boasts male fittings compatible with wide-mouthed Nalgenes that MSR proudly supports, and female threads designed specifically for 42mm Seeker bag spouts. Once both sides are securely locked in place, you...

Bike holder for the 32oz Nalgene Waterbottle. ...Will also suit other bottles of a similar diameter (92mm).</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p class="detail-setting printer"><strong>Printer: </strong>...

What is it?Strap for holding the Nalgene 1L bottle cap.Why make it?Original broke.Latest revisionDesigned with FreeCAD 0.19&nbsp;BOMTo be printed out of flexible materialAssemblyMount the small side on the bottle capMount the large side on the bottle...

This is a simple rack for Nalgene 1.2 mL screwtop cryovials (cat # 5000-0012), but may also be applicable to other products in the same product family. It is designed so that each well engages with the nubbins in the cryovial base to allow for...

Replacement of the broken part for my Philips LatteGo 4300 coffee machine.It's the small upper lid.

Did a little remixing to add a loop for my carabiner and reduce the stress of on the actual strap. ... Be sure to use flex, getting on the lid and bottle took a second but it eventually went on without modification.

<p>Did a little remixing to add a loop for my carabiner and reduce the stress of on the actual strap. ...&nbsp;Be sure to use flex, getting on the lid and bottle took a second but it eventually went on without modification.

A replacement lid for the standard 3.9" x 2.7" x 2" waterproof project box or enclosure is available on websites such as Aliexpress, offering a convenient solution for upgrading existing projects with enhanced protection against water and dust.

I found a nice heavy glass jar replacement from Seneca River Trading Company (https://senecarivertrading.com/glass-blender-jar-assembly-fits-kitchen-aid-ap7014452-ps16543616-w11528690 ) but it comes without a lid, and the original KitchenAid lid...

Lid for QCM