reprap prusa i3 rework 3d models
99392 3d models found related to reprap prusa i3 rework.thingiverse
... cuerno encima el sopporte del ventilador de la extrusora. Concentrara el aire en la zona de impresion. Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework 1.5 Rafts: No Supports: No Resolution: 0,35mm Infill: 30% Notes: PLA, 0,35mm layers
thingiverse
These are my parts fan mounts for the i3 rework. I included some open hardware-esque fan covers as well. I recommend printing the extruder T mounts horizontally for better structural integrity. The fan holders can be a littel fragile so be careful....
thingiverse
... infill 30%, wall thicknesses 1.4mm top bottom 1mm. Seems to be rigid enough like that. Printing done with the i3 at 30mm/s external sides, 50mm/s inner sides and 70mm/s infill, and extrusion rate at 110% to get some more chances of layers bonding.
thingiverse
Just added somosmake-r's way for better M10 washers fit. ...Corner is for M10 long threaded rods, M8 short rods, and 8mm smooth rods.
thingiverse
For E3DV6 on the PRUSA I3 REWORK 1.5 EMotion tech Reprap France
pinshape
SummaryEDIT 6/6/16 Added new version of the idlers. These new idlers have support for the bearings on both sides so it can't bend over and lose clamping pressure on the filament. There's a 0.4mm thick support material built in that you must cut out.
thingiverse
EDIT 6/6/16 Added new version of the idlers. These new idlers have support for the bearings on both sides so it can't bend over and lose clamping pressure on the filament. There's a 0.4mm thick support material built in that you must cut out. No...
thingiverse
The default is 23mm center to center for all four holes, which matches the Wilson TS, Wilson II, and Prusa i3 rework (at least). This does work on the Wilson II but only *before* the rack and pinion bed leveling mechanism was added -- I do intend to...
thingiverse
Just reworked a bit the original part. Now the belt of the Y axis may not slip away of the bearing's outer surface. Mounting procedure is a bit less simple though, requires to get all parts approximately put in their final location for them to be...
thingiverse
... of your printer does not comply with the above measures. ...for example: the number of gears , steps , etc Filament: ABS Extruder : 210c Bed: 110c Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework Supports: No Infill: %20 Post-Printing
thingiverse
This is a remix for mount LCD 12864 on a Z axis top left on Prusa i3 Rework Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework Rafts: Doesn't Matter Supports: Yes
thingiverse
X Endstop support for Prusa i3 Rework Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework Rafts: No Supports: No Resolution: 0.2 mm Infill: 100%
thingiverse
Fan diam 30 Print Settings Printer Brand: RepRap Printer: PRUSA I3 REWORK 1.4 Rafts: No Supports: Yes Resolution: 0.3 Infill: 30 Notes: PLA Ø1.75 FAN Ø30mm
thingiverse
PLA Ø1.75 FAN Ø40mm Print Settings Printer Brand: RepRap Printer: PRUSA I3 REWORK Rafts: No Supports: Yes Resolution: 0.25 Infill: 30
thingiverse
I wanted to add a 40mm cooling fan to the 1.5 rework from eMotion-Tech. ... Print Settings Printer Brand: RepRap Printer: Prusa i3 rework Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: .3mm Infill: 50%
thingiverse
I wanted to make a simple but directive fan duct : there it is. ...A new version there : http://www.thingiverse.com/thing:1575788 . Print Settings Printer Brand: RepRap Printer: prusa i3 rework 1.5 from emotion tech Resolution: 0.2
thingiverse
2 Options: Only print 2 of each : Lower part, 10mm and Nut For LCD compatible : 2x Lower Part,2 Nut and one of each other Print Settings Printer Brand: RepRap Printer: PRUSA I3 Rework Perso Rafts: No Supports: No Resolution: 0.3 mm Infill: 30%...
thingiverse
Reprap Prusa i3 Rework - Y-idler Reverse edition: Allows for either regular or reverse mounting Y-idler. Reverse mounting increases Y freedom by approx. 35mm. The Y-motor Reverse editions adds approx. another...
thingiverse
Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework Rafts: No Supports: No Resolution: 0.3 Infill: 30% Notes: Printed in PLA. ... Post-Printing Shopping list 1 x length of M8 threaded rod 6 x M8 nuts and washers 2x 608zz...
thingiverse
... was very nice use. NOTE: The fixation is 2 mm from the axel, because I need this space for my hot end. Print Settings Printer Brand: RepRap Printer: PRUSA I3 Rework Perso Rafts: Doesn't Matter Supports: Yes Resolution: 0.3 mm Infill: 30% honneycomb
thingiverse
... because X axis makes vibration which can force screw go down. Bottom part designed for NEMA 17 motor. Left side of the printer. Print Settings Printer Brand: RepRap Printer: Prusa i3 rework rev 1.5 Rafts: No Supports: No Resolution: 0.2 Infill: 20%
thingiverse
Print Settings Printer Brand: RepRap Printer: Prusa i3 rework Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.2mm Infill: 10% How I Designed This The fan support was designed to be easily and quickly printed. Therefore, the design is...
thingiverse
Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework Rafts: No Supports: No Resolution: 0.2 Notes: I didn't use any support printing this so since there is a 90 degree overhang expect to see some filament strings in the M3 polygon. ...Quick...
thingiverse
Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework modded Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 20 Notes: Use at least 0.8 mm for bottom/top and shell. I printed mine in blue ABS with 3mm filament. Post-Printing...
thingiverse
Print with support. ...Print Settings Printer Brand: RepRap Printer: prusa I3 Rework Supports: Yes
thingiverse
... from breaking down. ESP - Este sopporte protege la tarjeta electronica del sensor inductivo. Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework 1.5 Rafts: No Supports: No Resolution: 0.35 by layer Infill: 30% Notes: PLA - 0,4mm layers
thingiverse
... cooling object to be printed. For LED Headlight http://www.thingiverse.com/thing:1218714 Print Settings Printer Brand: RepRap Printer: Prusa I3 Rework Rafts: No Supports: No Infill: 30 Notes: Printed in PLA at 195° bed at 50° infill 30 (recticular)
thingiverse
I wasn't totally satisfied by the previous version (http://www.thingiverse.com/thing:1564502), so i changed the orientation of the output. ...Print Settings Printer Brand: RepRap Printer: prusa i3 rework 1.5 from emotion tech Resolution: 0.2
thingiverse
... Print Settings Printer Brand: RepRap Printer: Prusa i3 Rework Rafts: No Supports: No Resolution: 0.2 Infill: 20% Notes: Printed with MatterControl 1.5 Basic settings with above resolution and infill. Printed with $5 filament's Rainforest Green Adv.
thingiverse
... problems... I Upload the firmware of marlin RC7 that already setting up the auto bed leveling. Print Settings Printer: RepRap Prusa i3 Rework Rafts: No Supports: No Resolution: 0.3mm Infill: 20% How I Designed This Auto Bed Leveling Performance