reusable spool 3d models

There are new brackets to design, filament spool holders, rails, and carriages that go on those rails. The shelves need a bit more space too - I increased the gap from 9.5 inches up to 11 inches. It was a great way to fill my University summer break....

I tried a few different ducts and did not notice any difference, but after cutting off a set of original ducts, I found that it made a big difference with wind, but did not solve other weird motor spool-ups and wonky handling. I decided to redesign...

Materials needed: 4 - 608zz skateboard bearings (I got them on Amazon for $5.45) 1 - Length of either 5/16 or 8mm threaded rod 10 - 5/16 or 8mm nuts 6 or so 8mm washers 2 - 6-32 or m3 X1 1/4" or 30mm screws 2 - Nuts for the above screws 1 - 1/4-20 X...

If the design gets enough downloads&likes, i might get a spool of filament for free :-). All my latest creations will be available there, as Thingiverse downloads are a bit broken at the moment and also the customizers seems to not work anymore. ...

The are three sizes (small = 27 mm high, medium = 42.5 mm high, large = 52 mm high) the diameter is 49.5mm and fits inside a standard spool for storage in a zip lock bag or vacuum bag. Printing Print without supports lay the top of the lid and...

MBot's single extruder 3D printer kit is a fun and affordable option, but it falls short in one key area - providing an easy way to guide filament from the rear spool hanger up to the extruder. After considering a few alternatives, I decided on a...

Designing a new model of the original specs I changed the lip height along with a few minor changes. **I cut the the base and top by 10mm saving an hour each in print time and of course some material as well. *** Also added a file to join to spools...

Here's a design for storage containers and boxes that can fit your FilRight 1.5kg PLA (and most likely other) filament spool. There are three versions of the box: one slot, two slot, and three slot. I'm planning on making a couple more that are...

Install the compressor and fan by attaching them to their respective spools. 5. Next, connect the high-pressure turbine to the low-pressure turbine via a single-stage shaft coupling. Make sure the bolted joint is tightened in sequence, from bottom...

I haven't seen too many using the display screw holes - mostly spool holders, which are out of the question anyway when using enclosures. Some cons include: * It's fixed in height. I'm working on a customizable / adjustable version. Important...

As an added benefit, this design elevates the filament holder, allowing larger spools to fit. I've finally achieved a clean print after addressing my extruder stepper issue. The ball pivot works remarkably well now. I plan to create a v5 with a...

As mentioned in the title, it's a Laptop Riser!The hexagonal grid of the prusament spools makes very easy to attach some bolts and nuts to it. I was in need of a laptop riser that could release the neck pain of always looking down while working on...

All you have to do next is add some 3mm filament as a pin by clipping off a piece from a spool and inserting it into place. Then either print some caps or melt the ends so it stays securely in position. I haven't designed anything for 1.75mm...

If the design gets enough downloads&likes, i might get a spool of filament for free :-). All my latest creations will be available there, as Thingiverse downloads are a bit broken at the moment and also the customizers seems to not work anymore. ...

------------------------------------------------------------------------------------------------------------- Remix of the Spool-Holder from “Move in Z“ https://www.thingiverse.com/thing:5162457 Unfortunately I got the “newer” (cheaper) version of...

The Legs from the Lower Part of the Enclosure are Cut to Match My Eye Level, So I Don't Have to Stand on My Toes When Changing Spools. A Filament Guide with Dust Cleaner is Also Included at the Top, Where a PTFE Tube is Inserted from Below and...

 The holes are upsized so that 3D print squish doesn't cause any issues - I cut up a lot of little matchwood pieces with multiple thicknesses, and they all were inserted and held well (won't fall out if turned upside down).To use the paint...

Usually I just throw one in the bottom of each box, but was always concerned that the spools would crush the canisters. So, I made this holder in Tinkercad to hold the canister and allow me to attach it to the lid or side to keep it out of the way. I...

The enclosure body measures 19cm in diameter by 10cm deep, requiring over 24 hours to print, and almost a full spool of filament for a pair of speakers. It's likely deeper than necessary at 10cm, but I've included an alternative STL version that's...

You can find the Spool Holder here: http://www.thingiverse.com/thing:2097338, and the clamps here: http://www.thingiverse.com/thing:2190187. Edit: I added an improved filament guide that is stronger, looks better, and guides better. Edit2: I also...

Each one used approximately 120 grams of filament, allowing me to print 8 of these from a 1kg spool. If you reduced the wall thickness and bottom layers, and went light on the infill (it really doesn't need much, but give it some!), you could likely...

Works seamlessly with top or side mounted spools. Enjoy your creations and share them with us! ... If you found my Things helpful, consider treating me to a cup of coffee by using the PayPal button below: <form...

It should fit inside a filament spool. It should be easy to print and and don't require supports. It should be reasonably sturdy but don't waste too much filament. There are three different variants (best seen in the second picture): NoCore -...

Generating Attributions log: [0] Thing Title: Leveling Gauge for Your Printer [0] Thing URL: http://www.thingiverse.com/thing:29196 [0] Thing Author: LeftAngle [0] Thing Licence: Creative Commons - Attribution with Permission to Share [1] Thing...

Generating Attributions log: Thing Title : Egg Tray Thing URL : http://www.thingiverse.com/thing:43640 Thing Author : Jhack Thing License : Creative Commons - Attribution Thing Title : Minimized Heavy Duty Printable Filament Spool Thing URL :...

The original remix * Labelled the notches rather than have square and circular holes * had the ability to have as many, within reason, reporting notches as you want * allowed you to specify reporting at a %age or m left (label is always in m) *...

You've got leftovers on those spools? Any degraded plastic not suitable for printing something decent? Toss it in the trash-bin LITERALLY! This thing is also for you if you need a sturdy little bin that will take care of your trash after cutting off...

Human: FAQ: http://www.thingiverse.com/shivinteger/about [>>>] Generating Attributions log: [0] Creator: ttsalo [0] Thing Title : Moineau stepper extruder [0] URL : http://www.thingiverse.com/thing:15538 [1] Creator: TheGrum [1] Thing Title :...

These bolts are similar to those used in the original spool holders of my K8400. For center cover use 3M x 12mm screws, and be sure to secure all screws and bolts with 3mm self-locking nuts. I also had to remove a small corner piece from the bottom...

I intend to, eventually, make an insulated spool that fits over the core directly so that I don't have to fiddle with Super Corona Dope and parchment paper to keep the secondary coil from shorting to the core itself. I also made a little winding...