rf connector n type 3d models
247015 3d models found related to rf connector n type.grabcad
General N-type RF connector, 4 holes panel mount flange. ...For electronc design
grabcad
This is a model of a Amphenol RF N-Type Sealed Bulkhead LMR-400 Coaxial Cable Connector (p/n : 172220). ...This connector is good to 11 GHz.LMR-400 coaxial cable (0.0405" diameter) has very low loss at 3.5 dB/100 feet @ 750 MHz and has 0.223 dB/meter @...
grabcad
This is a model of a Amphenol RF N-Type Non-Sealed Right Angle Bulkhead Coaxial Cable Connector (p/n : 172363). ...This connector is good to 11 GHz.
thingiverse
Threw together something to have an alternative to sweaty fingertips turning my N-SMA adapters onto my VNA (Vector Network Analyzer). Turned out to be exactly the torque needed to put it on as if hand-tightened (not sweaty) if printed with PLA. ... ...
thingiverse
Derived from http://www.thingiverse.com/thing:661360. ... I needed two Type N connector caps at the same time. ...Easy fix since they're the same exact size.
thingiverse
A plug to cover the 17mm wide hole for a type N RF connector to keep dust and debris out. This was sized to fit the hole used in a Rohde & Schwarz SMJ Vector Signal Generator. The hole it fits is 17mm around, and the plug accommodates up to 2.5mm...
grabcad
Product Highlights: Gender = Plug-Jack Adapter Type = SMA male - BNC female Dielectric Material = TFE Fluorocarbon Retaining Ring Material = Beryllium Copper Gasket Material = Silicone Rubber
thingiverse
Groundplane antenna mount, 6mm radials based on a N- type or SO239 VHF connector. To be able to put on a 40mm mast. Checkout this website to calculate the specific antenna dimensions:...
grabcad
RF connector Patch Panel for 19" rack;16 port 5/8" bulkhead connectors;I usually put the antenna connections on the top row, and the radio equipment on the bottom row of Female-to-Female N-type bulkhead connectors
grabcad
This is a model of a Rosenberger N-Type Coaxial 1" 4-Hole Flange Connector ( p/n : 53K413-500N5 )that is good up to 11 GHz. The flange is 17.5mm square with an 12.7mm hole pattern. Note that this is smaller that other N-type coax connectors with...
grabcad
This is a model of a Amp / TE Connectivity N-Type Coaxial 1" 4-Hole Flange Connector ( p/n : 1057293-1 ) that is good up to 10 GHz. The flange is 25.4mm square with an 18.2mm hole pattern. Note that this is larger that other N-type coax connectors...
grabcad
This is a model of a Rosenberger N-Type Coaxial 1" 4-Hole Flange Connector ( p/n : 53K403-200N5 )that is good up to 11 GHz. The flange is 17.5mm square with an 12.7mm hole pattern. Note that this is smaller that other N-type coax connectors with...
grabcad
This is a model of a Amp / TE Connectivity N-Type Coaxial 1" (25.4 mm) 4-Hole Flange Connector ( p/n : 1-1337418-0 ) that is good up to 11 GHz. https://www.te.com/usa-en/product-1-1337418-0.htmlThe flange is 25.4mm square with an 18.2mm hole pattern....
grabcad
This is a model of a Amp / TE Connectivity N-Type Coaxial 1" 4-Hole Flange Connector ( p/n : 1058644-1 ) that is good up to 11 GHz with an extended insulation over a round center pin.The flange is 25.4mm square with an 18.2mm hole pattern. Note that...
grabcad
This is a model of a Rosenberger TNC RF Sealed Bulkhead Connector that is used with RG-405 semi-rigid coax 0.085" diameter (p/n : 56K511-271N5)
thingiverse
Simple N Type push on cover, great way for RF engineers to use up the end of filament reel using just 0.5m per print.
grabcad
SMA RF connector flnged with 4 holes. Brass with PTFE dielectric. ...Model based on the Tyco electronics part model 1478967.