right angle usb c adapter 3d models

a housing for the ULS-HE1004-3 NVMe to USB A und C chip. ... I use m2 screws to fasten the Drive and the Lid

Female USB-C Connector to mount in devices.This version is the 4-wire version.This model was manually measured, so keep in mind an error of ~1mm.

This user-friendly Alza USB-C cable holder securely attaches to any surface using strong double-sided foam tape for a hassle-free mounting experience.

I quickly made a customizable insert for this [Crafty Charging Stand by tbergman8](https://www.thingiverse.com/thing:2675463) to fit my chinese braided USB-C cable.

It is specifically modelled for:ControllerAZDelivery NodeMCU ESP8266: amazon.de2x USB-C Connector Female with screwholes: Aliexpress4 Big Screws4 small screws24AWG Cables AliexpressI have also created a schematic in the image gallery.LED StripIt is...

Needed a way to hide this ugly usb c dock. This is the solution. ... Just use some sticky tape at the ends, and Bob's your uncle!

Bars to “lay-in” laptop on Lenovo USB-C docking station. Use double-stick tape to fix it to the docking station. ...

This is a USB-C version of HeWhoMake's Under-desk Deej box. ...I modeled around [these Chinese arduino nanos](https://www.aliexpress.com/item/4000579100527.html)

ThinkPad Hybrid USB-C with USB-A Dock mount holder Unpacked Physical Specification (approximate) of the dock : Length: 210mm (8.27 in) Width: 80mm (3.15 in) Height: 30mm (1.18 in)

12 X SD5 X Micro SD5 X USB5 X USB-C1 X PencilStorage

This is just a small protective case for my MP07-IONA-US, the version with the USB-C power port. The lid snaps on and the board is screwed into the bottom using short M3 machine screws. Mine were around 8mm or so, but they really need washers or...

Customized version of https://www.thingiverse.com/thing:5404955 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5404955

0.187" (4.75mm) Quick Connect Female 18-22 AWG Crimp Connector Fully Insulated

Customized version of https://www.thingiverse.com/thing:2959749 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2959749

Made this variation to add a stylish fix to a damaged box of a board game. ...they do however look quite nice as D&D ground props/debris.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/dhqIJRcYbQp

Ergonomically designed and uses embedded magnets to aid in keeping your handsaw properly aligned with its large guide plane. You'll need 5 round magnets which are 10mm x 3mmThere are two versions available, one for a backsaw and another for a handsaw...

People create a straightforward OpenSCAD project for making brackets that attach a front panel to an enclosure. These brackets bolt securely onto the top and bottom edges of the enclosure opening, allowing the front panel to be screwed into place...

This part must slide smoothly into 3030 aluminum extrusions. It needs to snugly fit inside the extrusion without any resistance. ...The narrow section on one end of this piece, where it will reside inside the extrusion, measures precisely 7.8...

Just a simple no supports needed fan duct. I had a small failure without supports, but it was able to get cut off without too much issue and didnt interfere with stability or rigidity. ... Added 2nd version with 4 holes, might be a little easier to...

A customizable [inoculation loop](https://en.wikipedia.org/wiki/Inoculation_loop) whose loop is perpendicular its handle. ...Intended for use with the [Jubilee](https://jubilee3d.com/index.php?title=Main_Page) in [plant biology...

<p>The poles on my pergola were a bit wobbly, I designed and printed this to give to someone to have them make it out of metal for me.</p>

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/dhqIJRcYbQp

<p>This 90° Corner Clamp will give you a helping hand when holding 90° corners and "T" joints together securely during assembly. A second is included for “T” joints or to allow access for gluing. Great for things like constructing model buildings.

this model consists of 3 models this model was made on solidworks :)

Plastic cover for JAMMA harnesses in arcade cabinets. The exact dimensions of this are to fit a (non-original) harness in my Sega Aero City. The dimensions will need to be tweaked to fit other JAMMA connectors. The design of this requires zero...

I started with the NEMA 17 version uploaded by dasaki. The spiral tooth bevel gears were top-notch! Simple to print, they meshed flawlessly in the assembly. Bravo! You can find the bevel gears at his Thing (https://www.thingiverse.com/thing:372530).

Printed parts are now a single item, eliminating the need to assemble handle and spoon together. ... Print Settings Printer Brand: LulzBot Printer Model: TAZ 5 Rafts: Not Used Supports: Disabled Resolution: Optimized for ABS at high speeds Infill...

Attaches to a regular E-type slow-speed hand-piece allowing the dentist to conveniently insert or remove the abutment screw when the access hole is difficult to reach with a regular implant driver. Print one for every operatory! This is not...