rigol ds1054z 3d models
90 3d models found related to rigol ds1054z.thingiverse
Rigol DS1054Z Probe Holder. There is not much more to say about this. ... Fusion 360 for customization and export: http://a360.co/2CJeel3
thingiverse
This holder is designed in a way that a Rigol DS1054Z fits seamlessly on the holder. However, it is no tight fit so if you lift the scope, this won't stick to it. Feel free to improve this, I've also uploaded the Fusion360 project. The uploaded...
thingiverse
Rigol DS1054Z scope wall mount Remix of Rigol DS1xx4Z scope wall mount bracket" by Masterkookus - thinner - less material - reduced print time
thingiverse
It's an adapter you clip behind a Rigol DS1054Z Oscilloscope and put 3 Worx 20V battery to power it. No circuit required, batteries are in series on the AC input. ... Last +/-4 Hours on 1.5Ah Batteries
thingiverse
Table stand for the RIGOL DS1054Z oscilloscope with probe holders. The stand will raise the oscilloscope by 130mm to make more room on your crowded work table, and the screens won't be blocked by multi-meter or the soldering station anymore. There...
thingiverse
remixed to hold a lipo battery. ... Thanks Yanick Deguise for sharing the files!
thingiverse
This thing allows you to mount a 60mm fan inside the DS1054Z. I used a Noiseblocker PR-2. Now it is silent. One edge needs to be removed. ...Otherwise the fan pushes against a pin header on the main PCB.
prusaprinters
This thing allows you to mount a 60mm fan inside the DS1054Z. I used a Noiseblocker PR-2. Now it is silent.</p> <p>One edge needs to be removed. ...Otherwise the fan pushes against a pin header on the main PCB.</p> <h3>Print...
thingiverse
A remix of sb43201's scope stand. https://www.thingiverse.com/thing:2127891 The original version seemed scary to me at first. I thought it might be unstable so I remixed it to add a stabilizing brace (I designed it to accept a standard 5 gallon...
thingiverse
This is a replacement for the plastic ring that snaps onto the probes included with the Rigol DS1054Z oscilloscope. ...You can print as many as you'd like, and in any color!
prusaprinters
This is an adapter for putting a 60 mm fan into your trusty Rigol DS1054Z oscilloscope inspired by https://www.prusaprinters.org/prints/10300-rigol-ds1054z-converter-for-60mm-fans. I'm using a Noctua NF-A6x25 FLX with their low noise adapter NA-RC10...
myminifactory
Hello, i designed a front panel clip-on cover for my Rigol DS1054Z. In the downloads you will find two versions, one cut in half for printers with small print volume and one uncut for bigger printers. Clips must be printed by themselves and then...
thingiverse
Hello, i designed a front panel clip-on cover for my Rigol DS1054Z. In the downloads you will find two versions, one cut in half for printers with small print volume and one uncut for bigger printers. Clips must be printed by themselves and...
thingiverse
This is an adapter for putting a 60 mm fan into your trusty Rigol DS1054Z oscilloscope inspired by This is a remix from https://www.thingiverse.com/thing:398515. I'm using a Noctua NF-A6x25 FLX with their low noise adapter NA-RC10 (58 Ω series...
thingiverse
I got a new Rigol ds1054z scope that came with Rigol PVP2150 probes (the smaller, all black kind), and I needed something to hold the probes in place on circuit boards. I had already printed this very nice probing station designed by giufini: ...
thingiverse
I broke a foot off of my ds1054z oscilloscope, so i printed a new one. It doesn't perfectly look like the old one, or snap exactly like it, but it does work and it's better than having a one legged scope. ...it should be printable without any support...
thingiverse
Simple replacement knob for the Rigol DS1052E. ... My small buttons on my Rigol Oscilloscope cracked and the only replacements I've found to print don't fit.
thingiverse
mount your Rigol Oszi to a Wall. ...Attention, a 90° power plug is needed.
thingiverse
This is a lock for Rigols Probe. ...By attaching it to the probe, the probe's multiplier is locked to x10.
thingiverse
Siple Probe Holder for Rigol Probes (eg the infamous DSO 1054z) These do NOT clip in tight. However, they will not fall down if you brush the cables below. ... Very low insertion pressure is necessary to ensure probe longevity.
prusaprinters
Replacement knob for broken one on Rigol oscilloscope. ...6mm shaft.</p><p>Printed in white filament PM. </p><p><i>Print instructions: Layer height 0,1mm, no supports. </i></p>
cgtrader
Highpoly model of Rigol Oscilloscope for laboratory measurements. Modeled in Blender 2.9 and rendered by Cycles. Backside is not modeled ! Materials are PBR an textures made in Substance Painter in 4K. Decals Alpha included. All parts are unwraped.
thingiverse
I designed a stand for my Rigol DS1102 that would let my bench power supply sit underneath it. Perhaps someone else might find this useful. You'll need to print two copies of this STL file, one for each end of the scope. ...There is no crossbrace,...
prusaprinters
mount your Rigol Oszi to a Wall. ...Attention, a 90° power plug is needed.</p> <h3> Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p><p class="detail-setting printer"><strong>Printer: </strong>...
thingiverse
Parts-Holder for Rigol Probe Print Settings Printer Brand: Up! ... Printer: Up Plus2 ...
thingiverse
This probe tray is designed to store the probes of the Rigol 1054Z, Just because I didn't like the bags provided. ...The trays are stackable and comes with a lit for the one on the top.
grabcad
... thread, just a 2.5mm diameter hole. You can either tap the hole or just thread a M3x0.5 male thread into the clamp after it is printed. The outside diameter of the Rigol probe is approximately 11mm and the internal diameter of the clamp is 10.5mm.
prusaprinters
This probe tray is designed to store the probes of the Rigol 1054Z, Just because I didn't like the bags provided. The trays are stackable and comes with a lit for the one on the top. Category: Tool Holders & Boxes
thingiverse
The trigger button on my Rigol DS1052E oscilloscope broke (it cracked). So I needed a replacement one. ... Changes to blackboots' model: - made the number of ridges around the knob adjustable - the flat side on the shaft doesn't go all the way down...