robot chain 3d models

First, I modeled the front of the display to fit the RepRap Discount Full Graphics Smart Controller. Then, I also decided it needed a back to protect the circuit board. Easy peasy! Next, I tackled the problem of mounting a TFT35 touch screen...

... clean it up.  Pictured below are the on edge views of the dove tale design and the individual prints used in the above picture.If you decide to model your socket or light switch cover, the dove tail profile I used is shown below (units in mm).

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

Which means planning so the bridges will look nice enough/not stand out too much.This also means some very precise modeling so that the slicer can handle a bridged over area with a hole in the middle. Here, I build up to it layer by layer with...

The COMPLETE Swamp Gurunda bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! Swamp Gurunda (Presupported) The amphibious people of the swamps, with slimy skin and innate...

... of the Reitec polisher. 24.06.2022 - Updated the Drumgear to be the correct one. Sorry for the confusion. 24.06.2022 - Added alot of exemplarotry images / and Photos and added alot of BOM. 27.06.2022 - added alot of forgotten models. ...Sorry

Lightweight PLA tool is non-conductive, non marking and wont damage your materials if dropped the same as a heavy chunk of aluminum will.  Files Grouped in 5 Categories:MK3S+ Gcode Pre-Sliced - combined : All Files to build everything pre...

Update 01.04.2023 A friend i have made through the Neo Community have discovered that the clearance might not the good with the standart Neo, because the belt housing on the left stick out further, he have provided the file named...

Update to v9: Put the K25 spring into the model, looks like it fits fine with about 2 whole whopping inches of precompression. Rounded off the corners on the PR guide (which isn't much of a spring spacer anymore) to help the spring go smoothly. Now...

The new model isn't uploaded yet, but stay tuned for updates. 6/25/20 - This device has proven too effective. If left in the water for an extended period, it rapidly consumes the anode and produces copper oxide flakes. I can only leave it in for a...

(You may be able to get away with shorter bolts but these were the only ones I had that would fit) I have included a thumb screw model to make it easier to open and close the cover without a wrench. You will need an M3 heat insert but I cannot stress...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD on your own computer to process the code to create your own customized models. See DrLex's...

This is the first 3-D model I have built from scratch and I was looking to get it done quickly. So, I kept it simple but did note that it wouldn't take much to add a few more amenities that would suit personal needs or desires. The router fits...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 42 custom_bottom_fillet_resolution = 8...

In addition, in case you want to remix you would potentially only have to adapt the holder model.The bottom of the holder has a cavity that exactly fits a specific lightning cable found on Amazon with angled connectors to reduce the space it...

**Update October 26, 2017:** Since I was messing around with the model anyway, I figured it was time to do something I've wanted to do for a while. To decrease the "stack height" on top of my inexpensive flexy tripod, I slapped an 18.5mm ball clamp...

... The COMPLETE Sunken Kingdoms I bundle contains every model of this set, from the modular units to the heroes, the mount, the Pinup and the terrain piece! The Tritons are the proud folk of the seas, which ancestors are common to those of the Alfar.

I'm not sure how common this exact failure is but I figured I'd share it in case it helps someone from throwing out their cover and having to shell out for a replacement. There are other repair pieces for Audi/VW cargo covers which are used on wagon...

This model currently comes in 4 variations. Standard rail facing forward. Standard rail angled 5 degrees to the side off the rail. Standard rail with sidekicks facing forward. Standard rail with sidekicks angled 5 degrees to the side off the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

Refer to the pin diagram below.Connect the SMPS OUT- to a ground pin on the RPi.If you're using the fan, install it on the lid.Connect the fan's power and ground wires to pins on the RPi. My 5v fan was a little on the loud side so I used 3.3v and...

I found the models of the servo, sharpie, & 28BYJ-48 stepper motor on grabcad, but didn't include them in the fusion 360 assembly file here. The build log of my printer can be found here: https://openbuilds.com/builds/a-rolling-plotter.9207/ Here...

Update :Magnet Support Clip Hidden V2 - Added a slot for the 3rd magnet so now this piece with magnets can be used in the vertical orientation too.Parts to Print : All models have been printer at 200 microns, blade at 300 microns.Blood Splatter X...

For your Rubik's cube to keep the fluidity of its movements, it is necessary that the dimensions of the model are reproduced very precisely, and that your board can allow a first layer of 0.1 mm... Usually to deal with defects in the...

Not a problem with a well-tuned MK3S+.    The box was printed usingFilament                                              ...

Once I print and test it, I will update this with the final model and the STL's.\r\n\r\nI'm currently working on a new version with a removable tray for the Pi since I now plan to use a Pi4 with this project.\r\n\r\nI would not recommend printing...

By the way, even though adding a vertical ring might seem counterintuitive, it does provide added stability while still maintaining the original model's benefits: no need for supports, and you can print directly without worrying about brim or...

The water pipe has an improved shape that looks way better after being printed than the last model. Inner pot V2: made the border higher so there is more colour. SCROLL DOWN FOR DETAILED INSTRUCTIONS WITH PICTURES ! When using this flowerpot it's...

for the Firebrigade, working at hightSimilar thing on picture https://www.thingiverse.com/thing:6500617The most important mounting hardware used:-2mm dia tooth picks-3.2mm dia Mikado game sticks.-3.5mm metal screws for plastic (no machine screws!)The...