roll bar clamp 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_captive_rod_angle = 45 gopro_ext_len = 50 gopro_captive_rod_id = 3.8 gopro_secondary_what = clamp gopro_bar_screw_shoulder_th = 4.5...

Figured i would post it here as a template for anyone who wants to make somethig that needs a bar clamp. This clamp is designed for a 30 mm bar. It uses four #8 nuts and four 1 inch long 1/8'' machine screws or hex bolts. If you like this then...

I needed some new grips for my bar clamps at work, plus it was a perfect excuse to play around with TPU and Tinkercad. This is what happened as a result. ... To get started, I used the grip from another project that I had already begun working on for...

An altered Prusa bar clamp is used to install electronics boards, power supplies, and other items as desired. Numerous designs exist for attaching RAMPS/GEN6 boards and power supplies to a Prusa frame; however, they can be time-consuming to print. To...

The x-bar-clamp was altered to print horizontally, enhancing arch strength. The part width was increased to prevent narrow side towers from printing issues. Nophead's truncated teardrop holes were employed for added structural integrity. ...(Source:...

test fit the printed piece without the captive nut underneath of the clamp, and ensure your m3 bolt from the top slidey piece doesn't extend past the bottom of the clamp (where your bars will be) 1. place an m3 nut in the space underneath the printed...

i printed the friction patches in TPU 100%infill For one complete clamp you will need: Weight Bar Clamp Bottom x1 Weight Bar Clamp Top tabbed x1 Weight Bar Clamp main clasp hexed (or smooth variant) x1 Pivot Arm x1 Friction Patch (TPU) x4 :NOTE:...

Need a new bar clamp for your Reprap? Avoid overtightening issues by replacing all four clamps! This retrofittable option requires no unthreading of nuts, washers, or pulleys. Save time during construction by skipping pre-threading steps. Simple...

* Define secondary element as clamp-style, allowing for flexible customization according to your requirements by setting `gopro_secondary_what` to "clamp". * Select screw head size for the bar screws using dimension `gopro_bar_screw_head_d`,...

These were designed for all of my Harbor Freight quick release bar (parallel) clamps. I'm sure they'll fit several others. The full stand should be printed upside down to reduce the amount of needed supports. You could probably get away with no...

Simple bar clamp for 6mm rod, uses 3mm hardware. A small piece of electrical tape is applied to the rod to prevent slipping between the plastic parts. Works well on my Axial SCX10 Deadbolt. Print Settings Printer: Wanhao Duplicator i3 Rafts: Do...

I had a couple of those inexpensive bar clamps break on me, and when I looked around online I found plenty of the handles available but not a single top to match. That's why I decided to design one myself and share it with others so they wouldn't...

They created an awesome coupling for two HF bar clamps that let me double the clamp size, but I needed a way to attach a Wi-Fi camera. I used the coupling as is and added a simple mounting plate to match the camera mount, which resulted in this...

A printable bar clamp inspired by my son's toy version, this model is fully functional and comes with a customizable feature for size, thickness and grip handle adjustments. Note that the design lacks threads; you may need to use a thread cutter or...

this is the result. Started with the grip from this project since I had already started making one for home when I got the idea to fix the others at the same time. Print instructionsUnassociated tags: bar clamp Category: Tools Print Settings Printer...

I crafted a small clamp to secure an aluminum cooling bar onto my TMC2208 stepstick drivers. Caution: These are V2.0 BIQU BIGTREETECH TMC2208 drivers, with the chip positioned on top and a flat PCB on the bottom! Hardware: - [BIQU TMC2208 v2.0...

I'm always running short on clamp length, so I designed a coupler to combine multiple clamps. Created using Tinkercad, this coupler was printed with 50% infill at high speed and a 100% infill at low speed, both in PLA material. ...The lighter model is...

Stiffen up your 3D printer chassis. ... Add diagonal bars to the back of your printer.

for mounting items on 1 inch bar perpendicularly with bolt and nut

The pad fit my clamp very tightly and I had to hammer the pad onto the clamp and now it won't slip off, but lays flat so its parallel to the other clamp face. Therefore I believe it would fit smaller clamps as well. Inside dimensions of pad are...

To create the clamp shape, unclip the hanger and bend one half into a specific profile, adding a straight section at the top. Repeat on the other side. Secure the reel further by attaching printed clamps to stop movement. ...Two M8 bolts are required...

Specifically designed for Harbor Freight and Jorgenson clamps, it's essential to have one of these inserts for every six clamps. From the bottom, two screws can be threaded through holes to firmly attach it to the bracket. However, due to a 0.5mm...

... while the green one was printed with 100 percent infill at low speed. Both components were manufactured from PLA. A lighter clamp is suitable for light clamping tasks, but it's crucial not to tighten it excessively due to its inherent limitations.

I'm always running out of clamp length, so I designed a coupler to link multiple ones together seamlessly. This project was crafted with Tinkercad precision. To test its durability, I printed the blue coupler with 50% infill at high speed and the...

... these images: http://www.cnc-store.it/userfiles/image/LINEARE%20NBS_extract_1_Page_1.jpeg and http://www.cnc-store.it/userfiles/image/dim_shf.png. I hope you find it helpful. On 2014-10-14, I added a new internal clamp, L stile clamp, to the design.

Clamping Bolts Are 3/8" with Hex Heads - I Use Wing Nuts and Washers on the Other Side. No Post Processing Required There. The Rod Holes Are Meant for 3/8" Rods, But You Can Remix It Using Tinkercad to Whatever Size You Want. The Horizontal Holes...

... one at 100 percent in low speed. Both in PLA. The lighter one will do light clamping duty, but I wouldn't tighten it up too much. ...Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: No Infill: 100 Category: Tools

... a thing to mount my Logitec Clone webcam to the 16mm tent rails for the Creality Large Enclosure. ... I designed this clamp to fit a 1/4 -20 standard bolt (included) Depending on your camera you may have to trim back the bolt length a little bit.

... thing to mount my Logitec Clone webcam to the 16mm tent rails for the Creality Large Enclosure. ... I designed this clamp to fit a 1/4 -20 standard bolt (included) Depending on your camera you may have to trim back the bolt length a little bit. ...

I required a secure way to attach a ham radio antenna to the wing bars on my truck, so I designed this mounting system. It consists of a few strips of anodized aluminum, one of which holds the antenna and coaxial cable in place, while the others...