rsa token key 3d models
90619 3d models found related to rsa token key.thingiverse
This is a custom stand made to fit an RSA SecurID token which is attached to a lanyard. ...It takes about 35 minutes to print.
thingiverse
The Double RSA Token Holder sits on your desk and holds two RSA tokens for easy reference. It also travels relatively well. ...The tokens are held in place by gravity and have a slight slant away from the tether ring to make them less susceptible to...
thingiverse
I really like the badge holder design but also needed a carrier for my security RSA token so I modified to add the token "keyhole". ... Works great to cleanly keep the token and badge together.
thingiverse
... the noise down while walking. As can be seen in the photo, the RSA dongle still uses its own method of secure attachment, and the plastic restraint remains in place when clipped inside the snap strap, with or without the RSA token in place. ...
prusaprinters
A stand to hold up to two RSA SecurID tokens. Print instructionsExample printed in Fillamentum Wizard's Voodoo PLA. ..."0.20mm Quality MK3" setting in Prusa Slicer.</p> <p>Should print easily with pretty much any settings.</p>
thingiverse
Printed standing on its RSA bottom upright (tall) with no supports. Just a hint of "sag" on the final edge. it was so little, I probably wont correct it. if I do I'll upload. Printing upright took 7.5 hours but I was able to print several at a time...
thingiverse
This is a new version of my RSA Clip that attaches to the lanyard vs. the badge. I like my lanyard to sit higher on my chest when I use a retractor, so the clip is designed to allow the lanyard to be double wrapped to take up slack. If you don't...
thingiverse
This is an RSA key Holder designed to hold RSA over the PC Monitor. ...It can be modified to attach to any screen or keyboard.
thingiverse
Used to clip an RSA SecurID token to the lower bezel of a computer display.
thingiverse
This holds two RSA tokens securely. ...There are lanyard slots on the back.
thingiverse
... holders by adjusting the badge_width variable. If you print the clip on it's edge, it shouldn't need any supports. You will need to remove the key ring to install the token, and I re-installed the ring just in case the token slips out of place.
thingiverse
Holds up to a 64mm by 90mm badge and RSA token on the back, printed with supports for the top bridge. Uses a 6-32 ? ...screw for the RSA token but it friction fits pretty well already.
thingiverse
Clip for holding RSA key above monitor. ...Very handy if you frequently have to type your credentials in for telework.
thingiverse
It will hold two RSA tokens back to back. I added more bevels to the 2.1 version. It fits better to the round part of the token. It is a tight fit and will not slip out once two token are inserted. ...V2.1 STL file is also in the correct orientation for...
prusaprinters
I wanted a way to keep my RSA token with my security badges for work, and this was a good opportunity to grow some simple TinkerCAD skills. ...There's a satisfying snap when you pop the RSA token into place the first couple of times. (I'll add some...
prusaprinters
added more material between badge holder and rsa token holder for better structural integrity11/09/22: this one should be the right sizeCategory: Office
cults3d
added more material between badge holder and rsa token holder for better structural integrity scale down to 10% in slicer (I misnamed this one as the "Do It Again!" one - that one is now in the remixes section)
thingiverse
added more material between badge holder and rsa token holder for better structural integrity scale down to 10% in slicer (I misnamed this one as the "Do It Again!" one - that one is now in the remixes section)
thingiverse
Print between 10% to 20% infill. ...This holds two standard RSA tokens on a lanyard and acts like a bolo tie. ... v2 has slightly larger (2mm x 20mm) lanyard slots with a 7mm wide opening for thicker lanyards.
thingiverse
RSA token holder. ... Changelog: v0.1 - initial draft v0.2 - higher stand; tighter fit Print Settings Printer: Wilson II Rafts: ...
thingiverse
Gets lots of compliments from coworkers who are tired of hearing their badge click against their RSA tokens while walking. Uses 4x M4x12 or longer screws Updated 17 Jun 2018: Uploaded the v4 of the front and back, this version doesn't require...
thingiverse
I got tired of the RSA token bouncing around on my lanyard, so made a holder for it that fits a standard badge holder. Perfect for double sided badge holders. ... Fit is pretty snug, so it sits flush and doesn't bounce around
thingiverse
This is a remix of timbo's ID Card and RSA Token Holder. I changed the width to hold a single ID card for work. It took me several tries to print with acceptable results... probably because I fileted all of the edges to make it smooth. The final...
thingiverse
Holds the RSA fob at an angle for easy viewing. ... Instructions I printed with two shells and 5% fill in PLA
thingiverse
This is a remix of Gizmoticist's excellent RSA SecurID Stand.http://www.thingiverse.com/thing:343057 My company requires use of SecurID tokens to log into their services. These require a lot of data entry to authenticate and now you have to log in...
thingiverse
For your two-factor RSA token needs. If you use the loop built into the token, it's mass causes it to "bounce" noisily, and if you hit a harmonic in your walking it can start swinging. This is to hold it more securely on the lanyard itself. A...
thingiverse
Then we issued standard keys and added that to the design too! The OpenSCAD file is included for remixing. I would also accept requests for additional fobs. There are some tricky overhangs in the designs. Get your cooling right or do it with...
thingiverse
ID Card and RSA Token Holder for two RSA SecurID tags. ... https://amzn.to/38KGRK6