runcam eagle 2 3d models
954228 3d models found related to runcam eagle 2.
thingiverse
Based on the spec sheet from RunCam. Not my design but I modeled it. Is it perfect..no, will it work, yes. The holes are all within .001 mm of the tech drawings, the metal curves aren't perfect tho. ... My first model, enjoy!
thingiverse
Runcam Eagle 2 pod mount. Fits similar full sized Runcams 28 x 26.5mm . Can be mounted on the side of the plane. ...Takes two 3mm screws
thingiverse
Camera Lens Protection for Runcam Eagle 2. 100% infill at 0.3mm layer height. TPU. ... If you are looking for camera lens protection for Micro Eagle, check here https://www.thingiverse.com/thing:2884652
thingiverse
Martian II Side Plates for the RunCam Eagle 2 and Eagle 2 Pro. Camera has 0-45deg. Assembly requires qty 6 2mm x 4mm screws, the camera should come with 4 screws that will work directly. I found some 2mm x 6mm screws from previous RunCam Cameras so I...
thingiverse
Runcam Eagle 2 FPV Camera Mount for Martian 2
cults3d
Just my design of a eagle 2 camera protector for my armattan rooster 6 inch. ...Super Simple.
thingiverse
Just my design of a eagle 2 camera protector for my armattan rooster 6 inch. ...Super Simple.
thingiverse
The standard bakplate supplied with the Martian 2 frame does not fit the RunCam Eagle 2 because of the two connectors. The other designs I found was flimsy and could not keep the RunCam steady. ... This design is really sturdy and the camera does not...
thingiverse
This is a mount I made for the Runcam Eagle 2 and the Readymade RC 1.2 Ghz VTX (case removed with a heat sink added) for my FT explorer. Chances are not many people run this configuration but I figured I would upload it anyway. ...
thingiverse
... the first. The are screwed into the camera on either side with M1 screws I believe. This was made for the RunCam Eagle 2 but will probably work for any Runcam camera that have the 3 vertical holes along the side of the case. ... Printed in ABS.
thingiverse
Modified design of https://www.thingiverse.com/thing:2377043.
thingiverse
This is a remix of brochapman (https://www.thingiverse.com/thing:1707531) amazing work, it was the inspiration for designing the mount the way i did. This is sitting on a Goby 210 frame with a Race Flight Bolt v2, that is why the mount is shorter in...
thingiverse
This camera mount is specifically designed to fit the Runcam Eagle 2 Pro FPV camera with the 16mm dia. front lens and wide camera housing. This mount is mounted directly in the nose of the MTD - My Twin Dream (see pics). I have it mounted with about...
thingiverse
DESIGNED FOR **RUNCAM EAGLE V2** (its 3 2mm holes are 6mm apart). For me, (in Taulman 910) even though the measurements, the **Foxeer Arrow V3** also fits even though its holes are at a nice round 6.29mm apart (i mean - really?). In the photo...
thingiverse
My original v1 side plates and camera cage were leaving my large eagle camera exposed, so I designed a new set of camera plates to offer better protection. ... Printed in generic 98A TPU.
thingiverse
... ... The camera cage is remixed to hold a Runcam Eagle V1 instead of a swift 2, and I also made a VTX and RX antenna holder. ... In addition to the printed parts you also need the following: 6 x 20mm Spacer 3 x 28mm Spacer
thingiverse
This is a RunCam Micro Eagle mount for the Martian II 220 mm. Use the original screws to mount the camera in the angle you want. ... Import the part to your favorite slicer, duplicate it and mirror the mesh to get the opposite part.
thingiverse
This design is currently known to fit with: - Runcam Eagle 2 (full size) - Runcam Owl 2 + Check out my other things to find variants for other cameras. ________________________________ As the name suggests, you don't need to screw the camera into...
thingiverse
https://www.thingiverse.com/thing:4539843 Low drag FPV nose for Multiplex Funjet Ultra 2 designed to fit the Runcam Micro Eagle FPV camera. This nose also fit the regular funjet 2 and the old funjet and funjet ultra! Cutting the nose off a funjet...
thingiverse
Replacement / Better lens caps for lens caps for my Quads as I make them Print them in TPU rubber. ... I like to shade the tops with a Sharpie to show the sunken text.
thingiverse
Simple mount for mini size camera for Holybro Kopis 2
prusaprinters
Simple mount for mini size camera for Holybro Kopis 2 Print instructionsCategory: Toys & Games
thingiverse
I was searching for a mounting bracket for my Runcam eagle 2 but I could not find one. So I decided to make one my own. I made this bracket because the body of the camera is grounded so if placed in a metal mount connected to a carbon frame there...
grabcad
The Micro Eagle FPV Camera by RunCam. Includes .step files of each part and decals for the model, as well as a zip file containing SolidWorks models and an assembly. ...The assembly has 2 configurations for both the metal mount and plastic mount.
thingiverse
Dummy for the Runcam Micro Eagle. ...Overall dimensions should be close enough for testing stuff, biggest difference to a Micro Swift is the larger lens diameter.