ryobi shopvac 3d models
2676 3d models found related to ryobi shopvac.thingiverse
Shopvac insert and adpater for Ryobi wireless circular saw. You Will need to cut out a hole in plastic shielding to fit cover piece file over and also glue or mount on using small screws to make permanent. ...
prusaprinters
My miter saw is the Ryobi TSS103T. The inner diameter of the part that attaches to the miter saw is about 37.9mm (1.5 inches).The outer diameter of the part that attaches to the shopvac hose is 55mm (2 11/64 inches).I had to do just a little...
thingiverse
Customized version of http://www.thingiverse.com/thing:97238 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=97238 Instructions Using the following options:...
thingiverse
Adapter between shopvac and Ryobi Corner Cat sander. Replaces the cloth filter with a shop vac dust collection. Just pull out the cloth filter and replace with the adapter instead. 3D Print vertically as shown on the model. No support required....
prusaprinters
Connects the vacuum port on a 10" Ryobi sliding mitre saw to the suction hose of a Dewalt shopvac hose for easy clean-up. Includes a 30° bend to keep the hose out of the way when using the saw.</p> <h3>Print instructions</h3><p>Print standing up with...
thingiverse
Print was tight and needed a little sanding to fit. It works and is far better then having sawdust everywhere. ...Might want to scale up .1% to allow for shrinkage.
cults3d
Tool Sizes: Ryobi Sander dust port: 1.42” or 36mm ID Vacuum Hose (INCLUDES ALL SIZES): 1-⅞” (45mm) OD (Fits Ridgid/Dewalt/Ryobi standard vacuum size) 1-1/4" OD (Fits Craftsman, Shopvac 1-1/4" Vacuum hose size") 2-1/2" OD (Fits Craftsman, Ridgid...
thingiverse
I have an old Ryobi 10" Compound Miter Saw that was missing the dust collection bag. I designed this part to connect my small ShopVac to it. My ShopVac is missing the long hard end to the hose, and just has the corrugated hose. ...This part is designed...
cults3d
I have an old Ryobi 10" Compound Miter Saw that was missing the dust collection bag. I designed this part to connect my small ShopVac to it. My ShopVac is missing the long hard end to the hose, and just has the corrugated hose. ...This part is designed...
thingiverse
There are a ton of other vacuum adapters for different miter saws, this one is made simply to fit my older **Ryobi TS1340**, I wanted an easy dust collection method as the bag didn't work too well. This is a very simple pressure fit 'tube', that was...
thingiverse
Adapter to connect a Rigid shopvac to a Dewalt chopsaw.
thingiverse
Customized version of http://www.thingiverse.com/thing:1246651 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1246651 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651
thingiverse
Customized version of https://www.thingiverse.com/thing:1571860 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1571860
thingiverse
Handle for a Shopvac. ...My wife has arthritis and holding the large shopvac hose is difficult for her. This handle slides over the extension tube and is a friction fit providing a smaller easier to hold handle. ...
thingiverse
ShopVac Adapter for 1.75 inch to 1.75 inch hose from saw to vac I needed an adapter for my ShopVac Hose to my Compound Miter saw. ... This one in particular is my Bosch 10 Inch Gliding Dual Bevel Compound Saw
thingiverse
There is a test file that has the bottom rings to check if it fits on your shopvac and a single top piece to see if your accessories fit on. The outer diameter of the small is 45mm and the big is 50mm. ...The big has a wall thickness of 3mm and the...
myminifactory
This is an adapter for my 6 gallon shopvac with a 1.25" hose. My RIKON belt and disk sander (Model#50-112) fit no other attachments to connect to my vacuum so I made this up. The fit to the sander will be very tight but thats what you want with a...
thingiverse
... I used 10% fill and 2 shells. It printed on a Makerbot Replicator in black ABS in 3 hours. You can see it attach to the sheet metal part and the shopvac hose in the picture. ...I will probably duct tape it to the machine when I start to carve.
thingiverse
This is a diffuser/baffle for the exhaust port on a ShopVac-style vacuum. Instead of the air blowing out in a straight stream that kicks up dust/etc, this thing will redirect the flow in all directions, and create some turbulence, so that you can...
thingiverse
Assortment of Tips for the Shopvac Crevice tool. ... Use with the shopvac crevice tool http://www.thingiverse.com/thing:483682