samsung galaxy tab e car mount 3d models
553839 3d models found related to samsung galaxy tab e car mount.thingiverse
I created a wall mount for the Samsung Galaxy Tab E that I had sitting around to utilize it as a smart dashboard for Hubitat home automation. Its design to be used with M3 screws with M3 insert to mount the top face to the bottom base. You can mount...
prusaprinters
Designed to mount to a utility shelf. All parts printed @ 2mm w/ 3 perimeters, 15% infill except for the two small hanging posts which, for strength, were printed @ 1.5 w/ 4 perimeters and 40% infill. The ball and nut parts print together. Supports...
thingiverse
https://www.instagram.com/p/BsQVvjTlz91/?utm_source=ig_web_button_share_sheet First off the two things I used for electronics are right here: Tablet:...
thingiverse
This is a case for the Galaxy Tab E. Features: -Handle -Lockable Expandable slot -Lanyard holes -Usb Slots(fit adjusted/not tested) Printing: This is the biggest thing i have printed. I had an 8mm brim and it still tried to lift. I set...
thingiverse
Simple wall mount for Samsung Galaxy Tab 3 (SM-T210) 7 inch, portrait orientation.
thingiverse
Needed a Wall Mount so created this In two parts (Printed face down with Bed support) For my Samsung Galaxy Tab A8 10.5”
thingiverse
A wall mount for the Samsung Galaxy Tab A8, at an angle of 60 degrees, with two accessible screw-holes to attach directly to a wall.
thingiverse
Two piece wall mount for Samsung Galaxy Tab A8. ... There is enough clearance for front facing camera and brightness sensor to work.
thingiverse
Simple wall mount for a Samsung Galaxy Tab A 8''. ...I stuck it to a fridge with double sided adhesive tape.
thingiverse
This is my version of a Mavic Pro tablet mount, this mount is specifically made for the Samsung Galaxy Tab A7 with a silicone cover on it. No supports, infill is whatever you want, I went with 50% for strength. ... Hardware needed, just one 1/4 x...
thingiverse
For tablet (Samsung galaxy tab 6) for user interface home assistant. Speaker holes on both sides. ... After completing add some padding in the bottom corners and at the top for a snug fit without damaging the tablet.
thingiverse
I printed 4 of these so that I could mount my old Galaxy Tab to my kitchen wall with screws. ...It works really well!
thingiverse
Hi, This is a WallMount for a Samsung Galaxy Tab A8 (2021) model SM-X200. Five screw are needed. One to close de case and fourto fix the case on the support. I printed it on an Alphawise U20 with supports (see print settings section). The...
thingiverse
I was given a Galaxy tab as a promotional gift and it was destined to be a part of my home automation (domotica) system so I set out to make a nice wall mount that wasn't too large and allowed me to power it up permanently. This is for the Samsung...
prusaprinters
This is a minimalistic wall mount for the Samsung TAB A8 that prints without support and all the pieces should snap together without any modifications or glue.Everything else should be self-explanatory with help from the images I could not...
prusaprinters
I designed this wall mount so I cold mount my Galaxy Tab A7 on the wall to display HomeAssistant dashboards. The mount is attached to the wall using double sided nano gel tape which doesn't wreck the walls and is easily removable but super strong.
thingiverse
This wall mount holder is designed to keep your tablet on a wall for a smart home system.
myminifactory
I needed to mount a tablet on the wall so I can monitor all of my sensors through the OpenHAB application. It will probably work for other tablets of similar size.
thingiverse
... together. The hanging posts are designed to not bottom out so you can adjust for the thickness of your shelf allowing for a snug fit when hanging the mount. Be careful not to over-tighten the threaded bits. Hanging posts are 36.5mm apart. ...
thingiverse
Mounting can be done normally with 4 screws. On the upper side, a small hole has been left open with which the tablet can be restarted without taking it out of the box if necessary. ... # Support my work <a...
thingiverse
This wall mount case is for the Samsung Tab E 8 (SM-T377W). I just use 3m tape to fix it to the wall. Or you could use screws just make holes at the back of the print. ... Here a link to the tablet exact model:...
cgtrader
â¢Description: Realistic 3D model of the Samsung Galaxy Tab E 9.6. Model created in 3ds Max 2009. 3D Model detailed Polygonal Quads/Tris only. You can easily change all the parts of the object. Do not forget to check my other products... ...
cgtrader
â¢Description: Realistic 3D model of the Samsung Galaxy Tab E 9 .7 Collection. Model created in 3ds Max 2009. Available in the following file formats: 3ds Max with V-Ray materials 3D Studio (.3ds) OBJ (.obj) optimized for: Blender Cinema 4D...
cgtrader
â¢Description: Realistic 3D model of the Samsung Galaxy Tab E 9.7 White. Model created in 3ds Max 2009. Available in the following file formats: 3ds Max with V-Ray materials 3D Studio (.3ds) OBJ (.obj) optimized for: Blender Cinema 4D LightWave...
cgtrader
â¢Description: Realistic 3D model of the Samsung Galaxy Tab E 9.7 Black. Model created in 3ds Max 2009. Available in the following file formats: 3ds Max with V-Ray materials 3D Studio (.3ds) OBJ (.obj) optimized for: Blender Cinema 4D LightWave...
cgtrader
High Detailed High Detailed Samsung Galaxy Tab A 9.7 White 3d model with MeshSmooth applied. This 3d model main file format is 3ds Max 2009 and other formats are available can be used for all 3d applications. Product Features:: With Studio Clean...
thingiverse
When my son needed a car mount for his Samsung Galaxy J5 I designed this. It is intended to rest on a non-slip mat on a level part of the dashboard. It works perfectly and we also found it works great as a phone mount indoors. The stand has...