samsung ssd mounting bracket 3d models

A mount I designed to mount a SSD to the underside of a table.

A bracket to hang a Samsung T7 External SSD off the back of a laptop screen. This bracket is designed for a snug fit length-wise on the SSD, and 5mm is allocated for the fit on the monitor. It works well with an Asus Zenbook 15. ... Two clips are...

I have several Samsung T5 external USB-C SSD-drives. They are great. However having them lying around the desk was not cool or tidy. So I designed a vertical holder that can be attached to the back of monitor, wall or other surface with double-sided...

SSD mounting bracket for 2020 aluminum profile. I specifically made this for a GPU mining rig I am building. ... m4 screws needed to mount the bracket

[https://dfh.fm/collections/fasteners/products/threaded-heat-insert-nut?variant=39650196816041]Recommended Printing Settings:Infill: More than 25%Resolution: .2 (layer height)Nozzle: .4mmSupports: NoneInstructions:Print one of each of the model...

To assemble, you will need: * 2x Mounting Brackets * 8x M3x5mm Screws * 2x SSD's or HDD's, or mix-and-match :) Dimensions were based on mechanical drawings from:...

**Dell Laptop NVMe SSD mounting bracket** Replacing the HD in a Dell Latitude 5490 with an NVMe SSD, I discovered that it needs an additional bracket that is not supplied. *and* there was no design for one on Thingiverse, so I made one. (Follow any...

This is a minimalistic mounting bracket for up to 2 SSDs. Install the lower SSD first, since it provides support for the upper SSD. I highly recommend printing with at the very least 30% infill or even 100% since the strength of this bracket is...

2-part security mount for Samsung T7 SSD Installed in computer lab!

Tray to mount a Samsung T7 SSD under a desk or on the wall. Ventilation all around and leaves 1mm between the drive and the mounting surface for additional ventilation. Snug fit for my 500GB T7 (without the fingerprint sensor). If you're printing...

Wanted to screw a T5-SSD to a surface with easy removal. No USB-hole added (yet), might add this in the future. I printed mine at 102% in Cura, since it is designed with a very tight fit. ... Rotate the print 180 degrees to be able to print it without...

We initially offered the [1TB](https://www.lensrentals.com/rent/samsung-1tb-t5-portable-ssd) & [2TB](https://www.lensrentals.com/rent/samsung-2tb-t5-portable-ssd) models for fast data backups/transfers; however, our customers have recently shifted to...

This bracket can be used to mount an ORICO M.2 NVME SSD from Amazon to an object, most likely to a Camera. ...To mount this you need a 1/4-20 sink screw which is the standard for Camera mounting.

I might do some minor tweaking in the future including a design with less material and different concepts for mounting the SSD inside the bracket. The holes for the screws have a diameter of 4mm each, so almost any computer screw will fit. ... This...

... be mounted on the ends or between other modules. The holes are a bit tight so ream/file them out or use a hammer :p (just kidding, don't use a hammer!) The ssd can be mounted with the normal size mounting screws but you may need a different length.

Bracket for fitting a 2.5" SSD into a 3.5" HD bay

Here's a good link to a variety kit: https://www.amazon.com/CO-RODE-Notebook-Computer-Samsung/dp/B01GE9AK7I/ref=sr_1_3?keywords=laptop+screws&qid=1574496524&sr=8-3 Note that if you are using a mechanical hard drive in your Lenovo, then I don't...

This is a simple Samsung T5 SSD mount for your iMac. ...It hides the drives behind the display nice and neat.

This is an SSD mount useful for attaching a Samsung T5 SSD to the BMPCC4k/6k. It has a design where it lifts the ssd off camera slightly for hovering over the on switch and function buttons. ... You can print as-is for a normal snug fit, or what I did...

... save materials. Holes have been made a little larger to make it easier to pass through. The horizontal holes have been made so that they do not collapse during printing. Two types of SSD mounting positions (center and side) can now be selected.

remix for ssd samsung t5 tpu cover

This is a wall mount version of https://www.thingiverse.com/thing:2939627. ...No other changes made besides adding the 2 wall mount tabs for screws.

Simple and quick to print Samsung T5 SSD Wallmount with click-in mounting. Mounting is done with powerstrip or 2x M3 screws. The holder can be printed in PLA and holds the SSD firmly on the wall or under the tabletop. To remove the SSD, simply pull...

Samsung T5 SSD wallmount I also made a wallmount for two Samsung T5 https://www.prusaprinters.org/de/prints/42016-samsung-t5-ssd-dual-wallmount

Support SSD with a double-sided tape, on your computer to walk with your Samsung T series.

Depreciated! ...Use this one of me: https://www.thingiverse.com/thing:5521119 Deskstand SSD Samsung T7 This is a Remix of https://www.thingiverse.com/thing:5393314

Samsung 850 Pro SSD, measured with steel rule and vernier calipers. ...Not disassembled, so no internals and difficult areas to measure may be a little off spec.

This is a simple SSD sleeve I made for the Samsung T5. ...Mine fit very snugly inside so maybe increase the size a bit in the slicer.

https://bit.ly/2JyHNsP This is all well and good, but the ultra short cable that comes with the SSD makes for a cumbersome experience together with a mid-tower workstation. So i ordered a Deltaco 1m / 3.2ft long USB-C 3.1 Gen 2 male to male cable,...