sander with dust collection 3d models

... included so you can modify them as needed. The base that connects to the adapter is also modeled, providing a solid foundation for your adapter. With this setup, you'll be able to efficiently clean up dust and debris from your workshop in no time.

This is an adapter to be able to adapt a Craftsman V20 sander with dust collection to a 1/4" vacuum. ...It works exceptionally well as in my testing, there has been virtually no dust left over.

Dust collection adapter for the Jet 1020 drum sander. ...Converts the 4-inch outlet to a 2.5-in and redirects to the side.

Thanks to barty3d for the original design. ... Remixed this to make it hold an orbital sander with the dust collection bag.

... Sander. ... It will allow you to attach the tool to a 2.5 inch vacuum line for dust collection. I use a rockler and this works very well, but other lines are available. ... The ID tapers slightly allowing for a nice friction fit onto the vacuum hose.

Be aware that it may shatter with high speeds, and you probably will burn your grinder by using such a huge friction surface, so use low speed tools.\r\n\r\nTry 10x1.5mm instead, thread in a bolt without a head, and use your cordless drill on first...

The dust shroud sits on top and connects to the main trunk with a 2" dust collection hose. I used the magnets in the link below (because I had a couple laying around). ... Both the dust shroud and main trunk get 1 magnet each for them to hold them to...

The dust shroud sits on top and connects to the main trunk with a 2" dust collection hose. I used the magnets in the link below (because I had a couple laying around). ... Both the dust shroud and main trunk get 1 magnet each for them to hold them to...

... into an exhaust creating a venturi effect drawing sawdust with the power of the vacuum. This adapter will accept a 1.25" OD vacuum hose with a 1 1/16" ID. Part 4 is a backwards-compatible adapter for the muffler when not using dust collection

Replacement of the black rounded end panel to enhance dust collection. ... The port is designed for a 2 inch dust collection hose (as that's what i'm connecting it to, but you could easily put an adapter on).

Replacement of the black rounded end panel to enhance dust collection. ... The port is designed for a 2 inch dust collection hose (as that's what i'm connecting it to, but you could easily put an adapter on).

connection for dust collection. reduces 4" feed to fit a 2.5" hose. ...93mm OD to 58mm OD

Adapter from Parkside sander PBSD 600 A1 to standard 32 mm vacuum hose.

Fitting designed for Makita BO5041 5" Random Orbital Sander, but should work on any ROS with an output port OD of 7/8". You will also need a nylon lock nut and hardware to clamp the fitting to the tool. Recommend adding some thin craft foam or...

Customized version of https://www.thingiverse.com/thing:97238Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=97238

... for a 1-¼" hose out of PLA but it broke after a few uses. ...I also replaced my old ShopVac with a Dewalt model that use a 1-1/8" hose, so I needed a new adapter. ...I printed the new one out of PETG.</p><p>Supports are required for the small tabs.</p>

... collection. This might fit as well to other brands like Scheppach or Holzstar, but I did not test it, so I don't know it for sure. Please comment, if you know! See my other designs for further improvements for the dust collection of the BDS150

This allows you to replace the standard dust bag with a vacuum powered dust collection system, providing far superior dust removal turning your sander into a vacuum. Best quality when printed in PLA+, PETG. Tool Sizes: Ryobi Sander dust port:...

A handy dust-collecting hood designed specifically for a high-powered belt sander. Compatible with most standard vacuum cleaner nozzles. ... Check out the step-by-step tutorial on assembling, installing, and putting this system through its paces at...

A dust catch tray/bucket for an Enco 6" belt sander. This fits the sander shown like a glove, but may or may not fit other similar sanders. Note the boss that fits in the bearing recess on the end of the belt drive roller, and the arch that fits...

Extension of Dust Port for Hitachi Orbital Sander onto a Two-Inch Shop Vacuum Hose.

My spindle sander is quite old, made in the 60s, and has no dust collection at all. I made a dust collection hood that fits a standard 4 inch dust hose and is held down by magnets. The magnets were so strong that they pulled right out of the base so...

Adapter to allow 63mm dust port on Ryobi VOC RVC-1220I-G sander to 35mm inside diameter hose (Common on Ryobi Dust vacuum). Largest part fits over the dust output from Sander. ...Smallest part goes over hose from Vacuum.

... 2" OD dust port. ... Couples on outside of tool port and inside standard 2.5" dust collection hose.Customized version of https://www.thingiverse.com/thing:97238Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=97238

The compact dust port fits snugly into most shop vac vacuum hoses, providing a secure connection to capture dust and debris with ease. A powerful belt sander from Craftsman boasts impressive dimensions, measuring 4 inches in width by 21 inches in...

A versatile cover for capturing dust from a high-powered belt sander. Designed to connect seamlessly with a typical household vacuum cleaner outlet. ... Watch as it's assembled, fitted, and put through its paces in this informative video...

To fit a 63mm dust port onto the Ryobi VOC RVC-1220I-G sander, you'll need an adapter that connects to a 35mm inside diameter hose - a standard feature on many Ryobi Dust vacuums. The largest component of the adapter fits snugly over the dust outlet...

Adapter to mate a pool vacuum hose to the dust port of a Craftsman 20V sander.

An additional dust collection nozzle for my JET edge sander, to be placed on the table for extra suction. The nozzle features for holes for magnets so it's easy to be placed wherever needed. ... Hose connection: 75 mm Ø Dust nozzle size: 150 x 100 mm...

I based the design on the idea I got from this youtube video www.youtube.com/watch?v=XQpXGmeW6CE. ...My sander is sitting on a larger table so I couldn't go straight down It works well. ...Mod it as needed