scope cap covers 3d models
210780 3d models found related to scope cap covers.thingiverse
This is a basic scope/lens cover/cap designed to be printed in Ninjaflex, or some other flexible filament. The cap remains attached to the scope so you don't lose it. https://youtu.be/hjWDRI1EvLk It is designed to be used in Customizer. Just put...
thingiverse
Customized version of http://www.thingiverse.com/thing:1805188 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1805188
thingiverse
Customized version of http://www.thingiverse.com/thing:1805188 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1805188 Instructions Using the following options: font...
thingiverse
Customized version of https://www.thingiverse.com/thing:1805188 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1805188
thingiverse
Customized version of https://www.thingiverse.com/thing:1805188 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1805188
thingiverse
Customized version of https://www.thingiverse.com/thing:1805188 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1805188
thingiverse
Customized version of https://www.thingiverse.com/thing:1805188 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1805188
thingiverse
This is a simple lens cover / scope cap - designed to be printed using Ninjaflex or some other flexible filament. https://youtu.be/qhdmPw-kQWk Measure the outside diameter of the scope you'd like to print a cap for, and the Customizer does the rest!...
thingiverse
... http://www.thingiverse.com/thing:1803410 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1803410 Instructions Using the following options: Scope_Diameter_slider = 57.5 Resolution_slider = 100 Cap_Height_slider = 10
thingiverse
Customized version of https://www.thingiverse.com/thing:1803410 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1803410
thingiverse
Customized version of https://www.thingiverse.com/thing:1803410 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1803410
thingiverse
Customized version of http://www.thingiverse.com/thing:1803410 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1803410
thingiverse
Customized version of https://www.thingiverse.com/thing:1803410 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1803410
thingiverse
Customized version of http://www.thingiverse.com/thing:1803410 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1803410
thingiverse
I am experimenting a bit with how the Cap clips onto the Base. I am very open to suggestions on how to improve. I would recommend printing the "Base" in a flexible filament, and then scale it a bit down (0.9 - 0.95). The "Cap" and "Pin" is better...
thingiverse
Made for Bushnell 3-9X40EG -Objective lens OD: apprx. ...48mm (ID apprx 43mm) -Eyepiece OD: apprx. 43mm *Scope_Cap_part_01 and 02 (for eyepiece) designed sloppily and might update later
thingiverse
Covers for Rifle Scope 47mm and 44mm diameter with attach points to use rubber bands to hold in place.
thingiverse
i needed a 45mm cover for a 2x magnifier on my replica Aimpoint red dot sight. note1: a 4mm x 24mm screw works best. ...note2: the hinge can be a bit tight but you sort of want it to be like that, use sandpaper if needed Print Settings Printer: ...
thingiverse
A scope cap to avoid reflaction. ...or use this for the looks. scale or remix if you want. measurements: outer diameter= 46,6mm diameter= 42,9mm. depth (how far the cap is going in the scope) = 5mm. ...hole diameter= H:13,7 W:29,6 Brett.
thingiverse
A replacement dust cap for the polar scope on the EQ6 / NEQ6 telescope mount. ... May also fit the EQ6
thingiverse
This is for the front end of the scope,, usually store my rifle with butt / stock down... so dust usually clogs the lens Make spares.. I lost the originals in no time This fits the front of scope nicely.. but fits the rear loosely...Measured...
thingiverse
Lens caps to fit my Leupold scope with 43.1 mm OD. Scale this as required to fit your scope, or use the included Fusion 360 file to customize. Prints without supports with main face down on the build plate. There are lugs that fit 2mm bungee if...
thingiverse
Used ComradeQuiche original design and made a cap style retainer for small polycarbonate sheet