scotts edgeguard 3d models

I made this quickly in TinkerCAD to fill the open, interior void on my Scott's Edgeguard DLX spreader wheels. ...Per some owner advice on the internt, an 8 inch pie tin could be inserted and used, but I wanted to make something that looked more like...

As with many Scott's broadcast spreader users, I was plagued by the broken mixer arm and forced to use only a hair cotter pin to mix the fertilizer. But this makeshift solution didn't work well enough for me. I decided to redesign the mixer from...

... proving themselves highly effective! These paddles were specifically designed for the Scotts Turf Builder Pro Edge Guard spreader but should work seamlessly with any other walk-behind spreader that features a 0.43" hex shaft and 2" diameter paddle.

They've been tested with four bags of seed so far and work great! These were designed for the Scotts Turf Builder Pro Edge Guard spreader but should work with any other walk-behind spreader with a 0.43" hex shaft and 2" diameter paddle. Category:...

It's a holder to hold toilet paper rolls, it works perfectly with Scotts brand, not sure if other brands will though.

Designed this replacement knob for my scotts broadcast spreader handle to replace a missing knob. Using a 10mm nut as an insert that threaded onto the existing bolt this knob is a perfect replacement for a broken or lost handle knob. To print: ...

Tool to properly pull off the link arm on a Scotts Steering Damper for dirt bikes or motorcycles. I made this from Steel .428 thick, but could be any thickness down to 1/4". This and the bullet tool for installing the vane thru the seal so the seal...

I got a scotts elite spreader and didn't like that the paddles were just pins, So I made this one. There are a few different versions: half - is if you want to use the existing cotter pin to attach it. (single sided paddle) full - would require...

Scotts Turf Builder Spreader Tray the part that spins

These parts empower users to swap out their Scotts Mini spreader wheels for Harbor Freight alternatives, requiring a zip tie to secure the rear half rings to the axle. ...This inaugural project proved highly successful.

Tool for re-installing the vane on a Scotts steering damper. This prevents the sharp edge on the shaft from sheering the seal edge when installing the Vane. ...I 3d printed this but it need to be sized in a lathe, the printer struggled to hold the thin...

Scotts Instant Weed Remover - Reinforced T Handle Made for part number (SMG3095KCD) These tools are cheap, and they will break over time. Print in the direction the STL is in = (upside down T). Supports are needed - I just left the supports in...

All this current talk about "right to repair" is great, but for something like a Scotts lawn fertilizer spreader, you can't repair something if there are no parts to purchase! In just 3 short years my "pro" edge guard spreader went from new to...

Customized version of https://www.thingiverse.com/thing:1161218 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1161218

Customized version of https://www.thingiverse.com/thing:101307 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=101307 Instructions Using the following options: text9 = text8 = text7 = text6 = text5 = text4 = text3...

Scotts Turf Builder Spreader Tray the top part

DIY design of a possible way to mount a Scotts steering damper.

Purchased a bike equipped with a Scott's steering damper, but to my dismay, it lacked the original knob and cap. ...After fabricating replacement parts, they have performed flawlessly for an extended period.

<p>Lost or broken handle/turning knob for your hand spreader? ...Well here you go!Designed to fit a Scotts hand seed/granule spreader.Printed at .2 in Inland pla+&nbsp;No supports.

Crafted specifically for a Scotts Steering Dampener, this mount was designed to fit my 2002 CR250 model. ...Upon installation, it secured flawlessly in place, showcasing excellent compatibility and functionality.

Replacement main crank gear for Scotts Broadcast Spreader. The original on mine snapped off at the crank due to a rock being jammed in the spreader, so I built a replacement. The original part had a hollow shaft, but I couldn't see any reason why it...

The crank handle on my Scott's hand-held rotary broadcast spreader, which is over two decades old, finally gave out again. I managed to complete the job by rigging up my cordless screwdriver with a cordless screw and then examining the broken part...

My fix was developed for the Scotts spreaders that cause striping. The design from the factory puts the spinning impeller too low so the product hits the wheels and falls straight down. There have been easy fixes such as putting aluminum pie tins...

Top mixer part for scotts lawn food spreader.

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130

Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130

A personalized adaptation of the design found at http://www.thingiverse.com/thing:40704 was created using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=40704). ...Please follow these guidelines when customizing your order:...

Customized version of http://www.thingiverse.com/thing:1565695 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1565695 Instructions Using the following settings: MicroSD_gap = 3 units USB_gap = 4...

Lost the agitator for my Scotts hand spreader. ...Hope this helps keep a few from going to the landfill.