scx10 dual motor mount 3d models

Custom dual motor mounts for the k989. Standard fit with existing hardware. Symmetrical file for custom bottom plate designs. Print at 40% infill or above to avoid splitting screw holes with assembly. ...Recommend pre-tapping the holes with a screw...

Bumper reinforcement kit designed specifically for SCX10 and compatible models, featuring a sturdy mounting system for secure attachment to the rear bumper post. ...An upcoming image will showcase its installation process in detail.

This sleek winch mount fits perfectly with the Axial SCX10's robust design, requiring careful customization to meet precise drilling specifications. ...The result is a seamless integration that performs admirably, elevating the vehicle's overall...

This is a dual muffler version of this thing: https://www.thingiverse.com/thing:4639685

This is a mount for the Reefs 99 Micro winch, it mounts behind the Steering Servo on a SCX10.2 chassis. I used an old antenna tube to run the winch line through, I uploaded a version with a mount for a tube and a version with no tube mount if it is...

Two mounts and a guide to convert a standard-sized servo into a winch within the Axial SCX10 II frame. The converted servo is positioned behind the steering servo, utilizing all stock mounting holes for optimal results. ...To achieve best outcomes,...

I received a pair of scx10 ii ar44 axle housings, and I needed some link mounts for mockup.. I could not find any available so roughed out one in Tinkercad. They seem to fit pretty well but I don't expect them to hold up to serious crawling. ... This...

Mount the Tamiya Hilux body to your SCX10, either version one or two will do. I printed mine using PETG with a 100% infill and supports in place. You'll need to mirror it in your slicer for the other side as well. This should also work for the TF2...

The aim of this section is to elevate the bumper on your Axial SCX10 Honcho to rectify any clearance problems it might be facing.

3mm offset bumper mount to suit scx10 and scx10.2 frame can be inverted to suit desired height for fine fitment of bumpers may suit other chassis such as scx10.3 or element enduro

Rear cage pivot mounts specifically designed for the Axial Honcho rear cage are available, suitable for both SCX10 and SCX10.2 models of the vehicle.

The X-Y Axis Motor Mount for Dual 2-Extruder MGN12 NEMA17 Setup Features Separate Extruders.

Mount for L298 Dual H Bridge Motor Speed Controller https://amzn.to/3wRm0ml

This mount is designed to make it easy to install electronics on SCX10 style vehicles. Its hole pattern allows for multiple cable tie options. For a waterproof receiver, I use a balloon and some short servo extensions (check out Axial's balloon...

replaced original wooden pieces

A brilliant inventor has engineered an improved platform for attaching a standard servo to the SCX10's 11th axle. The design promises to offer a seamless experience, and initial tests suggest a perfect fit. ...Although it remains untested in real-world...

Changes made from the original: -1mm of clearance added to the motor mount screw holes to allow for adjustments -Mounted using T-nuts (allows this to be used on either side for dual Z setups) -Clearance cutouts for the screws mounting this to the...

Rear hinge mount for hard body Cherokee. ...Made it specific for my use but it might work for you too.

A easy way to relocate your receiver closer to the center of the chassis. ...Requires an M3 countersunk screw and double sided servo tape to mount.

Quick designs done to mount a body to a SCX10 Clone chassis.

I have remove top mounting bracket from left side front mount because stepper motor will fit there, also move mount over 1mm extra to clear side of stepper motor, lowered the power supply mounting and added extra support under front bracket. ... Updated...

This is my innovative design, take it for a spin - it's a winner when paired with an RC4WD Bruiser body attached to an SCX10 chassis, and it'll also perform flawlessly on the upgraded SCX10.2.

My Designs for a Dual 370 Motor Setup are Almost Ready My latest project involves creating a custom dual 370 motor setup for my B36 chassis, which is still waiting to be printed. I plan to position the motor mount inside the C-rails for extra...

Because N40 motors are significantly larger than the N20 motors I normally use, I redesigned the dual motor mount and created a custom Dual N40 motor mount for my WPL/JJRC cars. I successfully tested this design on my modified WPL B-1, and it...

I have a dual Z axis system, so no frame mounting holes for right motor mount. Also noted that left frame mount slightly elevated stepper motor off of base frame. Modified design to allow for T-nut securing so I can use for both left and right...

a dual y stepper motor mount for the ender 3. this version decreases the bed size to about 180mm, so you will need to adjust your firmware accordingly. ...or, you can use my pre compiled marlin firmware for the BTT SKR E3 TURBO that is made to be used...

They also designed an X-carriage for a Prusa that can accommodate Jim's Flying Motor Mount Dual Extruder and includes a fan mount for nozzle cooling fans. Detailed instructions and updates on future plans are available in the Instructable...

When using two same axle housing halves, you loose two pillars for mounting servo plate. I made a 4-link truss that integrates servo mounting pillars too. I recommend not to screw into pillars but put a nut (locknut) on the other side of the pillars....

Here's a revised remix of the Scuddy Dual Z Upgrade Kit for the Ender 3, tailored specifically for Geeetech A10/A10M printers that utilize a second stepper motor for enhanced dual-axis functionality. To accommodate this upgrade, I've modified the...

Here is the rewritten text: Top-right Z bracket for a Dual motor (Dual Z) moved to the top-left position.\nMirrored the original top-left bracket, relocated the motor mount to allow for unobstructed X-carriage movement and end-stop detection without...