scx10 dual motor mount 3d models

This is a custom BoSnap dual extruder mount. The second stepper motor on hand was shorter in height than the original, requiring a new bracket to fit properly. Designed specifically for this purpose, the updated bracket holds its own and passes the...

My previous mount is sagging, so I redesigned it with dual gussets for improved supports.

--- # new ones: ** https://cults3d.com/en/3d-model/tool/z-motor-mount-single-dual-ender3-pro-v2 ** --- two options: - one with an extra vertical support that slides on the side Y beam. it will keep the motor elevated, not touching the side Y beam,...

Additionally, I added a mount for dual nozzle cooling fans. A print cooling solution will be forthcoming soon. Dual-extrusion printing may not be far off! For this project, you need two 25mm, 12V fans. Assemble and print the carriage as per the...

... and small voltage drops generated by brushed motors. The post also includes links to Thingiverse group for WPL designs, YouTube video showcasing the motor mount, RCGroups forum thread, and Banggood website where Adrian purchased the N20 motors.

Remix of the single fan mount of the Kraton collection. Made it hold two 40mm fans. I use it in my Arrma Kraton EXB in a 4092 Rocket motor. Printed in PETG with support. ...Fixed with straps.

Print in PETG or better I already had made a motor mount but this is one with a redesigned rail (using caliper to measure and tested multiple tolerances) to fit the creality aluminum extrusion perfectly (to a point that it probably won't work with...

I'm conducting an experiment with a custom-made mount that integrates two high-torque motors, each equipped with 6-inch propellers. ...Although I haven't conducted any tests yet, I'm optimistic about the outcome and expect everything to function...

... for an MN99s RC Defender 90. ...In order to keep the driveshaft not too bent, I decided to tilt/angle the motors so the shaft is better oriented. The mount slides over the chassis frame and is held into position thanks to 2 screws. ...Ses pictures.

**I redesigned a new model which available for free on my patreon page: https://www.patreon.com/posts/63463457** ------- Last update: added one with motor that is also adjustable in the X direction, 1mm from center in each direction (and Y) file: "Z...

For my build I am also using a 30mm spacer on top of the extrusions and with the bearing plate and the top mount I am using 5mm hardware with a 55mm shank and the motor mount screws are m3x8mm. ...The spacer has a wire guide for the Z stepper on the...

This custom replacement part is specifically designed to work with both the Monoprice Dual Extrusion 3D Printer and the Makerbet Replicator 2, allowing for seamless compatibility and integration with these popular 3D printing devices. The innovative...

This is a remix so it can b used with second Z Axis motor (does not have V-slots). Use with stock screw, and add 2pcs of M3x6 to motor screw in. ...

This is a remix so it can b used with second Z Axis motor (does not have V-slots). Use with stock screw, and add 2pcs of M3x6 to motor screw in. Category: 3D Printer Parts

This is a remix so it can b used with second Z Axis motor (does not have V-slots). ... Use with stock screw, and add 2pcs of M3x6 to motor screw in.

PLA, 15-20% infill, no supports (except for skis which need supports) Compatibility (as tested): Wing/airfoil: 6-8" cord, 20mm thick Motors: X2206 1500kv Sunnysky (18g), or similar mounting pattern (not typical) ESC: 21mm max width, (12A velotech, 1A...

The following components have been tested for compatibility: * Wing/Airfoil: 6-8 inches cord length, 20mm thickness * Motors: X2206 1500kv Sunnysky (18g) or similar mounting pattern, which is not typical * ESC: 21mm maximum width, such as the 12A...

I appreciated the design of that mount from Koplari, but the extruder lever arm would interfere with my CR-10 S4's vertical support. ...So, I decided to create a modified version that addresses this issue.

Yet another part for my low hardware version of a core xy. ...this uses a 5mm rod instead of more screws or bolts. This is for 3030 rails. the mount can be used on either side. it's printing now. ...will update.

I built this modification for my personal project vehicle. It's functioning perfectly so far. ...Feel free to share a copy if you decide to produce it.

This is a dual servo mount and longitudinal battery tray for the Axial SCX10 and clones that use 70mm wide front crossmember.

A custom-designed motor mount is needed to prevent catastrophic collisions between the z-motor carriage, hot end, and extruder Bowden. ...This upgraded mounting system must accommodate both dual z-axis and single motor configurations.

Proline Wagon Bumper Equipped with Front Servo Mount, Designed Specifically for Axial's Scx10 and Scx10 II Models.

Heavy duty one piece servo mount plate for the Axial SCX10 II (AR44), INJORA, AUSTAR

Redesign of the SKYRC Motor Dual Fan Mount #SK-400008 with integrated M3 5.5x5.5x1.8mm "flat" Square Nuts at Layer 4.35mm when printing first layer with 0.15 and following with 0.2mm. 2023-04-22_18:23: Just uploaded v2_1 v1 which is a bit beefier...

... This setup also allows the motors to help turn the plane if needed. There's only one fixing at the rear because the nutball plane slips into the motor mount and is the main support. ... This project is still in progress, so parts may change.

Hi guys, Have you ever had a TRX4 with no transmission and a spare SCX10 cheapo Chinese transmission and drive shafts kicking around? Well, I did, AND I didn't feel like spending $55 on a TRX4 trans right now, so I modelled up this mount. Note: The...

ESC mount for the SCX10 III to mount the larger MAMBA X ESC above the micro servo. Requires 2 x M3 x 6mm Screws and uses stock holes for mounting. Print in the orientation downloaded. ... 5 walls 4 Top & Bottom Layers Print using PETG

Created an exact copy of the SCX10 front bumper mount using my 3D printer. The mounting holes might need some additional drilling due to varying printer tolerances. ...To ensure a secure fit, I intentionally designed the holes slightly larger than the...

SCX10 Center Side Mount ESC Tray Designed For Stock ESC, May Fit Others. Dimensions Are Optimized For Seamless Installation. To Secure The Tray In Place, We Recommend Using Longer 3x12mm (AXA436) Self-Tapping Screws That Will Provide A Rock-Solid...