self watering planter 3d models
99550 3d models found related to self watering planter.thingiverse
https://www.instructables.com/3D-Printed-Self-Watering-Planter/
thingiverse
Yet another self-watering planter. ... Designed to be easy to print and parameterizable.
thingiverse
This is a self watering planter I created while tinkering around in Tinker Cad
cults3d
Yet another self-watering planter. ... Designed to be easy to print and parameterizable.
thingiverse
This thing was inspired by ParallelGoods Self-Watering Planter. ...this was made for interiors with right-angle design.
thingiverse
This is a Self watering Planter parts to be printed 1.plant holder x1 2.water holder x1 3.absorber x2
prusaprinters
Self-watering planter designed for my carnivorous plants.You can customize dimensions in Fusion 360 using "Modify->Change Parameters".
thingiverse
Square self watering planter. Lid is option and held on with M3 screws. ...All parts can be printed with no supports
thingiverse
This is self-watering planter designed for my carnivorous plants. You can customize dimensions in Fusion 360 using "Modify->Change Parameters". ...
thingiverse
I have created a remake of the self-watering planter (https://www.thingiverse.com/thing:903411) with a bigger pot. ... Enjoy !
thingiverse
... lug jars (those little jars that jelly comes in and also a lot of salsa? ...Note that it does _not_ fit Mason jars!) For more info on why and how I made it, plus the OpenSCAD code: http://blog.tommy.sh/posts/adventures-in-self-watering-planters-part-1
thingiverse
The Self-Watering Planter was designed to be 3D printed, easy to setup, use and clean; while at the same time allow for customization through mixing and matching different colors for the pot and reservoir. ...Be sure to check out the Instructions tab...
thingiverse
Tiny self watering planter. There is 1-layer thick support which you should remove with sharp knife. Also you need a small piece of rope 5cm/2" to make self-watering work. ... And don't forget about seeds and soil!
cults3d
Tiny self watering planter. There is 1-layer thick support which you should remove with sharp knife. Also you need a small piece of rope 5cm/2" to make self-watering work. ... And don't forget about seeds and soil!
thingiverse
A self-watering planter for the **Customizer** - inspired by Agustins planter. This makes it easy to adapt to the size of a given vessel. ... The pots in the photo are eaten up honey jars.
cults3d
A self-watering planter for the Customizer - inspired by Agustins planter. This makes it easy to adapt to the size of a given vessel. ... The pots in the photo are eaten up honey jars.
thingiverse
Small self watering planter. Watering can be done from the hole in the center of the pot. Stick some rags in the holes to pull water into the soil. ...This print can be done without supports.
cults3d
The Self-Watering Planter was designed to be 3D printed, easy to setup, use, and clean; while at the same time allow for customization through mixing and matching different colors for the pot and reservoir. Be sure to check out the Instructions tab...
thingiverse
Hex Self-Watering Planter Reservoir Base (L) 99.7mm x (W) 88mm x (H) 70mm Pot (L) 99.7mm x (W) 88mm x (H) 114mm Remix Ithttp://www.thingiverse.com/thing:903411/#comments
myminifactory
It was taken from an original pineapple planter created by DasMia (https://cults3d.com/en/3d-model/home/pineapple-container) and remixed into a self-watering planter. The top piece has a hole in the bottom for 100% cotton to be thread through to...