shimano tl pd40 3d models

I was looking for a quick easy tool with fast printing. Easy to put in a vice. ... Thanks for the original design, it was easy to remix it quickly.

Remixed with some flanges removed to make it printable without supports.

Shimano pedal tool TL-PD40to be used with a socket wrench 22mm

The key for Shimano pedals, an analog of the Tl-PD40, is also suitable for pedals of other manufacturers.  ABS, 3 perimeters, 35% infil

Shimano sells the TL-PD40 for this purpose, but I don't have a large enough wrench or the appropriate Bottom Bracket tool to turn it with. So I whipped up a version that will fit the BB tool I do own, a Park Tool BBT-9 for my Hollowtech II BB. ...I also...

Shimano pedal service tool TL-PD40-BTL-27L a tool to disassemble the shimano pedal. Similar to the TL-PD40 tool. can be used in combination with a 44 mm bottom bracket tool. ...I use it together with the BBB/BTL-27L.

This is a Shimano Tool (TL-FH16) to Install the outer seal Ring (Y3FM26000). ...For use with Shimano microspline freehub FH-M8110-BS, to set the correct deep.

This is a custom tool that shimano uses to fix the lock-ring onto the chain ring on shimano steps electric bicycles. I changed the sizes slightly for a better fit on the nut and to fit within the plastic chain ring guide. This design also uses a...

This should get you out of trouble if you need to tighten/loosen the chainring on an E8000 Shimano motor. ...I don't think it would last long term but go me out of trouble.

For those wishing to remove the front chainwheel on a Shimano STEPs ebike you need a tool to remove the left hand threaded lock ring. This ring is a different size to the usual shimano bottom bracket tool. Print Settings Printer Brand: ...

This tool helps you to remove the chainring of your shimano steps ebike. You'll need a 32mm spanner/socket wrench to turn the tool. NB it's a left-hand thread, so turn right to loosen! This remix from pvdm's version adds a smaller hole. You can...

Shimano TL-FC24 bottom bracket puller adapter, for SM-BB9000. ... Shimano TL-FC24 bottom bracket puller adapter, for SM-MT800.

SHIMANO TL-EW02 DI2 TOOL FOR E-TUBE CABLE

Shimano TL-LR15 (cassette puller) amazon.com link: https://www.amazon.com/Shimano-TL-LR15-CL-Rotor-lockring-tool/dp/B000F5LLAS bike-components.de link: https://www.bike-components.de/de/Shimano/Kassettenabzieher-TL-LR15-p1086/

It requires having the TL-FC25 Adapter, which is included with the compatible Shimano BSA bottom brackets. Trying to reduce the need to buy many of the rarely used bike tools... save the $12 or so Amazon charges for this tool. For mounting and...

... Holowtech II crank. ... Can be used by hand, with a 23mm spanner. or with a 5mm allen key. Herramienta para colocar y quitar el tapón de la biela Shimano Holowtech II. Puede usarse con la mano, con una llave de 23mm. ...o con una llave allen de 5mm.

Shimano Hollowtech II TL-FC16

This tool allows you to adjust the Bottom Bracket axial preload on Shimano Hollowtech II cranksets.

Tool to tighten (or disassemble) shimano pedals like PD-540 SL or PD-5600SL

Stronger design with higher wall thickness throughout and reinforcements at the relevant points. ...Fits perfect on my Shimano Steps Lock Ring (Y78N00085, Drive Unit DU-E6100). ...

This device enables fine-tuning of the non-drive side crank arm's bottom bracket bolt on Shimano Hollowtech II cranksets. ...Losing mine means I can print new ones via 3D technology whenever necessary.

Therefore, per Shimano specs and instructions, the cap must be first tightened to the spec and then the crank retaining bolts tightened. I did not have a 1/4" to hex drive adapter, so I remixed the original to have a standard 1/4" drive...

Scaled down version of the TL-FC32. Fits the newer BB-MT800 and other smaller Hollowtech II bottom brackets. Printed with 7 Shells and 50% Infill. ...Works nicely, fit is a bit loose, could be scaled down a bit, maybe 1-2%, but works as-is...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

This is a light wrench to remove cassette gear by mean of a Shimano TL-LR15 tool. Useful in bike travels. Version 2 is a reinforced version, but both are strong enough. ...

This is similar to Shimano's TL-AF10 tool. The tool is a snug fit on the hub, make sure to press it down into the tabs. Shimano says to tighten the dust cap to 5-6 N-m. The dustcap is made of plastic, don't over tighten it. ...The threads on the...

This is a 16-Notch 41mm diameter Shimano bottom bracket installation and removal tool that replaces the Shimano TL-FC24 and TL-FC25 adapters. It works with Shimano BBR60 and BB-MT800 bottom brackets. ...It is to be used with a 1/2" or 12.7mm square...

Tool for plugging/unplugging SD-EW300 wires for the new Shimano/Dura-Ace 8100/9200 Di2 wires. ... Have tested with EW300 wires (non-I) and seems to work like a charm!

I needed a tool to drive my Shimano crank bolt with, so I whipped up this simple adapter to convert to a hex driver. ...Fit perfectly on the first try REMIXED added a circle for the holding fingers ( as in the original parts )

If you've dismantled a set of Shimano M324 pedals and found you really don't want to pay for the special tool to hold the outer cone while you tighten the locknut, give this a try. It's designed to fit as snugly as possible round the 13mm head of...