skadis ferrex multimeter 3d models
5545 3d models found related to skadis ferrex multimeter.thingiverse
A multimeter holder compatible with Ikea's Skadis pegboard. Wider that most holders already on thingverse to accommodate a larger multimeter with the cables already plugged in. I printed each component separately and used a glue gun to glue the...
thingiverse
Updated Skadis multimeter holder. ...Joints are much more sturdy and has enough room to hold a large multimeter, as well as probe holders.
thingiverse
Multimeter holder for IKEA Skadis board. Designed for 68x23mm sized multimeter, but can be used with anything with same size. ... Uses hooks from [IKEA SKADIS Universal Hook Set by CSD_Salzburg](https://www.thingiverse.com/thing:2853257)
myminifactory
A holder for a small multimeter hung on an Ikea Skadis pegboard. Uses a M4x15 CSK screw and nut to secure onto pegboard.
thingiverse
i wanted to place my multimeter @ my ikea skadis pegboard ... and so i simply designed a little hol(e)der. ... Just print in place with supports for the hooks
thingiverse
Multimeter holder for the Ikea Skadis Pegboard The Multimeter is 60mm X 30mm X 90mm The holder has two holes for the Pins on the Side. ... I printed it on a Creality Ender 3 v2 If you like the Design feel free to send me a Tipp:...
prusaprinters
Printed easily on my PrusaMini, PLA+.Support is needed for the hooks. Fits well my UT33D+ multimeter.OpenSCAD source file is attached. The hooks were copied from @marco (https://www.printables.com/model/260795-skadis-box-openscad/files)
prusaprinters
This tray is designed around an Extech MN16A multimeter but it can work with others. ...Requires 2 of my universal peg plates.Print with supports.The holder could be used with other pegboard systems if you design peg plates for it.
thingiverse
... so it doesn't rock or put extra torsion on the attachments. I went with seperate attachment hooks and holders so that each could be printed as easily as possible, and so that the hooks were less likely to break when attached to the Skadis pegboard.
thingiverse
This design is made for Biltema multimeter that you can see here: https://www.biltema.se/verktyg/matverktyg/matinstrument/multimetrar/digital-multimeter-2000018521 Probably it will work just fine with other multimeters, the inside measurements are...
prusaprinters
Designed around the low cost Kaiweets KM100 model multimeter. ...The cutouts allow storage and use while mounted.</p><p>Print using supports for the pegs on the back of the holder. </p>
thingiverse
... 2018 - primarily the holes for the hooks, and the hook. Mashup/designed in Tinkercad. Make To make this design, print one Skadis Multimeter Mount and two Skadis_Universal_Hooks. ...I printed this at .20 layer height, 10% infill, using generic PLA.
thingiverse
Just a quick remix to allow herman_v96's multimeter mount to fit an IKEA Skadis board. The universal hook from CSD_Salzburg is also included. ...Just print the mount and two hooks and you are good to go!
prusaprinters
... the holes for the hooks, and the hook. Mashup/designed in Tinkercad.MakeTo make this design, print one Skadis Multimeter Mount and two Skadis_Universal_Hooks. ...</strong>I printed this at .20 layer height, 10% infill, using generic PLA.</p>
thingiverse
This is a container for the Ikea Skadis pegboard to hold the Brymen BM235 multimeter. Dave Jones from EEVblog sells a branded version to support his Youtube channel. I originally designed it so you could leave your leads connected, but that became...
prusaprinters
This is a container for the Ikea Skadis pegboard to hold the Brymen BM235 multimeter. Dave Jones from EEVblog sells a branded version to support his Youtube channel.</p> <p>I originally designed it so you could leave your leads connected, but that...
prusaprinters
Just a quick remix to allow herman_v96's multimeter mount to fit an IKEA Skadis board.The universal hook from CSD_Salzburg is also included. ...Just print the mount and two hooks and you are good to go!</p><p> </p><h3>Print...
thingiverse
Remix of the 80mm Container for a small Multimeter with a hole in the front and downside for cables.
thingiverse
Multimeter probe holder, that can hold 4 or 8 probes. They are designed to fit together next to each other and are able to hold common probes with a diameter smaller than 12 mm and a sleeve smaller than 16 mm (common chinesium, Brymen, Fluke, Rigol...
thingiverse
Handy Ikea Skadis mount for Hantek 2xxx series multimeter.
cults3d
This is a holder for a VOLTCRAFT multimeter for an IKEA SKÅDIS. It was tested with a VOLTCRAFT M-4650B, but probably many others will fit (inside dimensions 39mmx91mm). But since I only have this, I can only verify this. It has minimal wiggle room to...
thingiverse
... but missing the hook part. ... I didn't want to waste the already printed holder so created in Fusion360 a simple hook for it, using the same approach as in Skadis Hook System, but thicker and with different dimensions to fit the multimeter holder.
prusaprinters
Hier eine Halterung für ein Multimeter für die Skadis Wand von IkeaAls Boardhalter sind einfache Clips vorgesehen die Einfach eingeklebt werden.Dadurch ist die Halterung sehr einfach druckbar.PLA Prusament 20% Infill 3Layer 0,2mm
thingiverse
I combined the universal hook with this multimeter holder in order to make the support stronger and tighter fitting.
thingiverse
holder for multi meter on skadis pegboard using back support. ... 6/3/2018 -updated design
thingiverse
Remixed wall mount for skadis https://www.thingiverse.com/thing:3908072
thingiverse
I needed a multimeter holder for the ikea skådis that was big enough so wouldnt have to remove the cables. The holder is 100x70 excluding the small sidemouted holder. I use that for the probes. ... You need 2 of the skadis container hook from...
thingiverse
... 42 mm in depth and it is 98 mm from bottom to the top edge as indicated on one of the pictures. The cylinder on one of the pictures for holding the wires is from the IKEA SKADIS Container-/ Shelfset - link: https://www.thingiverse.com/thing:2851040
prusaprinters
Made for use with two (2) Universal Hooks from : https://www.thingiverse.com/thing:2853257/files Huge thanks to CSD_Salzburg for the hook design. My multimeter is about 70mm wide and 26mm thick.