skyhunter 3d models
187 3d models found related to skyhunter.grabcad
Hi, I measured and created the Skyhunter model with Photomodeler. ...The inner part of Skyhunter is metric, the outer part is not metric.
thingiverse
Sharpened version of Brandis Skyhunter Heroscape
thingiverse
This is a simple support for the delicate tail of Skyhunter.
thingiverse
A support for 36x36mm flight controler, jsut plug it on the rear wood place of the skyhunter.
thingiverse
Here are the parts for the Vtol Nano Skyhunter. I will add the parameter files as I finish the project. ... It is still a work in progress.
thingiverse
This part mounts to the 4-bolt pattern on top of the SkyHunter wing. ... Used for this video: http://www.youtube.com/watch?v=OgGsPaCVdjY
thingiverse
Some landing gear for the big skyhunter. ... Best to use something like Armadillo Filament for this print as it needs to be super strong!
thingiverse
Various parts I utilized for my Mini Skyhunter VTOL conversion. Flight Controller and Battery trays were inspired from grahame addicott designs. The boom mounts are for the stock boom tubes and some additional 10mm tubes. ...
thingiverse
This is my design for SkyHunter motor mount. It is tested with SunnySky 2820 motor. I'd used M3 screws and nuts for mounting motor. ... The recommendation is using 200mm printing with 75% infill, but it can be vary.
thingiverse
Various parts for a SonicModell mini Skyhunter. ... Battery tray Motor mount TBS Crossfire Nano SE mount Matek VTX mini mount Generic FPV camera mount x2 wire tidy's All designed to be printed in PLA.
thingiverse
This is a improved version of the standard flimsy washers that come with the Micro or Nano skyhunter kit. ...It generates a bit more surfaces to hold on and secure the wing to the fusalage.
thingiverse
I redesigned the canopy to fit the Sonicmodel version of the Nano Skyhunter. Print the two pieces and glue them together. ... There is a slot for at 10x2,5mm neodym magnet.
thingiverse
Here are the parts for the Nano Skyhunter I built to learn Ardupilot. I will include the Parameter file as soon as I finish the built. ... It is still a work in progress.
thingiverse
I redesigned the Mini Skyhunter tail mounts, because the original ones are sooo heavy (20g each), this version is just 12g each (PETG, depending on print settings) This part might also fit for the big Skyhunter (1800mm), but I'm not sure (let me...
thingiverse
GPS mount for the full sized Skyhunter model. Made to fit a BN-280 but should fit anything similar sized (28.5mm X 28.5mm X 9.5mm). Couple different passages to run wires to main compartment. ...Sticks up above the foam about 2mm.
prusaprinters
GPS mount for the full sized Skyhunter model. Made to fit a BN-280 but should fit anything similar sized (28.5mm X 28.5mm X 9.5mm). Couple different passages to run wires to main compartment. ...Sticks up above the foam about 2mm.</p>
thingiverse
Tail brace ends for Skyhunter 1800mm. These are for 1mm x 4mm CF spars. They are a little loose as I needed them this way due to the ends of my spars being distorted from cutting with snippers. ...A little super glue in them does the trick.
thingiverse
This is a motor mount for the SkyHunter FPV plane. The hole spacing for the motor is 32.5mm. The pegs are 5mm in diameter and you will be required to drill out holes in the foam of your plane. ...This will make the mount much more secure.
thingiverse
I made this canopy to replace the standard foam canopy of my micro / nano skyhunter. Since Iam probably the only one still using a Immersion 600mw VTX I also included a blank model of the canopy so remixed can be made for other FPV setups. ... If you...
thingiverse
The SkyHunter is a big plane...and I don't like taking mine apart. It needed to get off of my floor and up on my wall! These mounts hole the Sky Hunter by the tail boom. Print 2 and use the tail as a guide for where to install them. The version in...
thingiverse
Hello Guys and Gals, This is the parts i used on my build of the mini Skyhunter, the motor mounts (foam parts) are from an Albabird and I've used the cowls from a that build. Motors are 2216 1250kv sunny sky The antenna mount is for the bigger...
thingiverse
A mod from a few other plans to fit on skyhunter 1800mm with mobius The camera plate is a mod of :http://www.thingiverse.com/thing:2014056 The baseplate is a mod from: http://www.thingiverse.com/thing:1645843 Gimbal controller:...