skyhunter 3d models

The Skyhunter Main Gear STL I designed makes launching my 1.8M Skyhunter easier. Originally, I used the nose gear STL from Finwing that they provide for their Albabird model. I tested this gear with my Skyhunter swinging a 13" prop and it worked out...

This is a very strong and unfortunately quite heavy set of landing gear for the Skyhunter 1800. I made this because I consider hand-launching this plane to be way too dangerous with a 13 inch propeller installed. The suspension can handle rocks up...

Parts list: Full-size Skyhunter: https://www.banggood.com/Skyhunter-1800mm-Wingspan-EPO-Long-Lange-FPV-UAV-Platform-RC-Airplane-KIT-p-1176011.html?p=DG23031123036201501P Sunnysky 2820 motor:...

I just got my new Sonicmodell Skyhunter Nano, but it came without the stock motor. I decided to upgrade to a quad motor 2204 instead. The fuselage firewall is buried in foam, so I didn't want to risk damaging any of the foam when installing the new...

... flat, so a slight tilt will be necessary when mounting a camera. My hope is that this remix will serve as a valuable enhancement for your mini skyhunter project. With 3 perimeters and 20% infill, this model weighs approximately 16 grams. ...Cheers!

You can find all the information in this article on my website: http://www.sop-fpv.com/tecnologia/item/28-mini-skyhunter-vtol-y3-parte-i, and http://www.sop-fpv.com/tecnologia/item/29-mini-skyhunter-vtol-y3-parte-ii. Edit: I have replaced the...

Installed a cc3d mount into my nano skyhunter receiver plate, forcing it in violently. What an unrefined solution! Thanks for your efforts, altermac. Should work with ~16mm m3 screws, but I'm using 18mm because that's what was available. Be cautious...

Skyhunter Quick-swap camera mount ======================== Introduction -------------- This is a camera mount designed for the top canopy of the full-size Skyhunter. It maintains good aerodynamics while offering multiple options for various camera...

Cheers Parts List: Full-size Skyhunter https://www.banggood.com/Skyhunter-1800mm-Wingspan-EPO-Long-Lange-FPV-UAV-Platform-RC-Airplane-KIT-p-1176011.html?p=DG23031123036201501P Sunnysky 2820 Motor...

This is an all in one FPV mount for the Nano Skyhunter, it might work on other planes. It is designed for a standard HS1177 FPV camera, a Matek VTX-HV, including a mount for the SMA bulkhead that comes with the VTX. ...I glued it to the deck lid using...

Mount to attach Mele Quieter3 (or 3C) to iOptron SkyHunter tripod. One model set for tripod legs, another to mount on tripod riser. Use a 5mm x D7.0 heatset insert to secure the two pieces together around the riser or the leg of the tripod. You...

This is a custom TX03 Camera mount tailored specifically for the Eachine Micro Skyhunter.\r\n\r\nNot yet thoroughly tested; however, designed to securely screw into pre-drilled 20mm separated holes on the canopy section. The holes on the mount are...

This is a remixed TX03 Camera mount designed for the Eachine Micro Skyhunter. Not yet tested; but designed to screw into pre-drilled 20mm separated holes on the canopy section. Holes on the mount are designed to take M2 (2mm) self-tapping screws to...

The goal is to build a Skyhunter full-size 1800mm with a tilt rotor VTOL mechanism and design a tilt motor mount for it. BOM: For one side of the wing for the front mechanism, you'll need: 1 Motor: I'm using SunnySky x2814s 1250kv, but any kind...

I'm going to fill every blank space perfectly, making sure that nothing is left out, and ensuring a seamless flow of information from start to finish. I will be completely thorough, leaving no room for errors or inconsistencies. ...My goal is to make...

You'll likely require additional support, as well. ...The pre-drilled screw holes are designed specifically for the original fasteners; however, you might need to slightly deepen the recesses to accommodate your chosen hardware.

The original rudder feels too mushy. Replacing it with stiffer components will make all the difference. ... I'd rather have it printed with PETG for enhanced heat and sunlight resistance.

I'm excited to share my first contribution with this community. I've been working on a project that's still in its early stages, but I thought it might be helpful to others, so I'm sharing my progress. As part of the design, I had to experiment with...

This is tailored for the Radiolink GPS (SE100) - https://www.amazon.com/dp/B01IUSVXOA/ To utilize this, first remove the Radiolink GPS from its original casing and carefully transfer it to the custom-printed housing. ... If you appreciate what has been...

I added this feature to prevent the screws from over-embedding in the foam wing, which causes uneven stress distribution. ...This design spreads the load out more uniformly.

This design conceals the area intended for a GPS unit, providing an uncluttered appearance for your aircraft even though not every pilot utilizes this feature.

This is the critical component that securely fastens the hardware to the fuselage, allowing the wing to be mounted properly. ...The precisely engineered holes enable straightforward threading of the standard screw from beneath and the addition of a...

I decided to create a customized holder for my GPS device, selecting the Sky Hunter's front cutout as the ideal location. The design consisted of two separate components, which I carefully inserted the GPS pole into the foam, positioning it...

This is a lightweight edition of the original, weighing in at just 3 grams compared to the standard version's 6 grams. Less weight on the tail translates into better performance. To ensure optimal results, print with a single perimeter, as there...

These are components attached to the ends of the wings to increase the wing span from 1.80 to 2 meters.

I wasn't thrilled with the original canopy design, so I decided to create my own. Right now, it's being printed out, and once I finish putting together the interior, I'll post some photos online. ...Thanks for swinging by!

I'm not the best at modeling so I remixed the winglets design and made a bottom plate to make transport a little easier. I used gorilla glue to secure the wing joiner to the main part of the wing while the rest of the wing slides on. There's a...

Lightweight and small support for making vertical stabilizers more rigid. Print and glue in place. ... Parts weight less than 5g (2.4g each) so it won't add any real weight to the tail wing.

Main wing is NACA 4412.Vertical and horizontal tails are NACA 0009.The fuselage shell is 15mm because that is the side wall thickness. The actual thickness of the top and bottom is 20mm. The thickness of the fuselage bottom is modeled pretty...

I'd love to give this design a remix to make it all fit together seamlessly! Let's get creative and make some changes. To start, I'm adding a special feature: a hole that allows you to pass a wire through for the elevator servo. This will make it...