slash 2wd drift 3d models
10548 3d models found related to slash 2wd drift.thingiverse
Printed for a Traxxas Slash 2wd. (The 4x4 setup is different) This one doesn't use bushings or bearings, so it might wear out quickly. Seems to hold up pretty well though. Thanks, Enjoy! ...
thingiverse
I adjusted the size to fit a 2wd Slash. The fit might be a little tight, but over time, it will break in. ...Fill at 100% to ensure strength.
cults3d
All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm screws....
thingiverse
All of the stands I have found are for the Traxxas Slash 4x4, so I took it upon myself to design a simple stand for my Slash to keep the wheels off the ground when in storage on the shelf. For assembly, you need the following: (8) M3x10-12mm...
thingiverse
Wanted a simple, cheap & quick to build and repair 2wd chassis with variable length to fit a Skyline bodyshell which is in process, had some old Kyosho parts kicking around and steel electrical conduit so threw this together.. it worked out great and...
thingiverse
hey, made some skis for my slash 2wd. ...skis are printed with pla and linkages with flexible filament https://youtu.be/sRequv5ERdY
thingiverse
This is the first of many print sets for a 2wd Slash down-force system. Suitable for both drift and drag cars. When the whole system is installed your car should pull itself down and make the car squat as speed increases. This fits with and without...
thingiverse
This is a simple flat ESC Mount that fits in the stock ESC location on the stock Traxxas Slash 2WD Chassis and the LCG Chassis. It might fit other models that use the XL-5 ESC because that's what these holes line up with. The plate is 55mm x 55mm. I...
thingiverse
This is an experiment to extend the wheelbase of a Traxxas Slash 2WD to fit Arrma Infraction or Felony bodies. It makes the wheelbase 76 millimeters (3 inches) longer than stock. It is designed around the Slash LCG chassis, and I have no idea if it...
thingiverse
This is a simple wheelie bar I designed for my Traxxas Slash 2wd VXL, as it was spending far too much time on it's roof! In addition to the printed parts you will need the following parts - 2x 625 bearings 2x M5x20 countersunk head bolts 2x...
thingiverse
I wanted to drift my Slash so I designed so sweet drift covers for the tires, they are very tight fit, but once you get them squeezed on they drift so awesome, and with the plus of using way less time and fillement than making a whole tire, I did try...
thingiverse
traxxas slash 2wd rear bumper mount compatible with asciencepotato's 4wd bumper. ...It's a little fragile, so please drive carefully.
thingiverse
Body Mount Extension as Add-On to the original Body Mount of the Slash 2WD to fit the Proline F150 1979 body in the front. ... Built with Tinkercad.
cults3d
esc mounting plate for the Traxxas Slash 2wd trucks with the LCG, low center of gravity chassis. This allows you to securely mount any esc that you would like using double sided tape or another attachment method of your choosing. ...This changes the esc...
thingiverse
This is designed for a traxxas slash 2wd it allows you to mount the transmission backwards for better centre of gravity and cornering ability but you can also mount it stock. ...this was designed to be cut out of aluminium but can also be laser cut out...
pinshape
This is a Traxxas Slash 2wd LCG Chassis - Sidewinder SCT ESC Holder Bracket and FS-RG3E Receiver Holder. The Castle Sidewinder 3 SCT with phan will need 2 - 3x25mm to hold it in place. ... The FLYSKY FS-RG3E will need one 3x12mm and a little shoe...
thingiverse
I designed these mud guards for a Traxxas Slash 2wd High center of gravity chassis to keep the dirt out of the chassis. It uses the holes from the nerf bars so you will need 4 screws that are a bit longer to replace the ones from the nerf bars. ... ...
thingiverse
Maybe it can fit on the other 2wd Traxxas as well with some modifications. It is based on the new style of clip on straps presented on the Traxxas 4TEC 2.0 and TRX4. The only modification required to the car is enlarging the hole where the hexagonal...
cults3d
Maybe it can fit on the other 2wd Traxxas as well with some modifications. It is based on the new style of clip on straps presented on the Traxxas 4TEC 2.0 and TRX4. The only modification required to the car is enlarging the hole where the hexagonal...
thingiverse
This is a very simple chassis saver I designed for my Traxxas Slash 2wd with High Centre of Gravity chassis. Proline used to make these a few years ago to eliminate the weak spot where the transmission bolts to the chassis. Unfortunately, when...
pinshape
This is the Front Caster Block for a Traxxas Slash 2WD, Bandit or Rusler. Print them if you break one... PLA Holds up ok in mid Temp and Cold. I PLA is fine for normal racing conditions. I raced for 1 hour accident free with oit breakage. They...
thingiverse
I made this 0 degree bulkhead to make my slash into a drag car. Works great! ...Print flat with supports touching buildplate for best results!
cults3d
wheelie bar for traxxas drag slash use m3x16mm screws these could be used for show or as templates to fit bodies
thingiverse
... for a reinforcement for my slash front tower and could not find one, so I decided to make a functioning mod. ...Goes directly behind the front shock tower brace on the 2 wheel drive slash to help stabilize the wobblyness when landing off big jumps.
thingiverse
These should also fit in the rear of 2wd Slash models. I printed these in PLA with .25 layer height with only 2 walls and 10% infill. I tested them out on somewhat rough pavement and got 2 full runs out of them before they were used up. If you...
prusaprinters
I needed extended body mounts for a monster slash build and didnt want to buy them. ...Printed in PETG, we will see how well they hold up but its cheap to print spares</p><p>uses m2.6 x 12mm wood screws to attach the posts</p>
thingiverse
From El Cheapo labs I have made this tube reinforcement for my low budget Slash Drag car. This will also fit other Traxxas models using the same axle. This is one of many economy parts that I will be releasing. Anyone can go cash bomb a rig, let's...