snapmaker 2 a350 3d models

Assembling my SnapMaker 2 - A350 left me craving a solution for cable management, prompting me to design a custom plate that screws into existing holes. ...To bring this vision to life, four additional M4 * 12 Hex Screws were required, and I'm thrilled...

... and has some slop to it just in case the rails are a bit too close together. I also elongated it. I haven't tried their dividers yet, but if they don't fit, I'll likely redo them. I have printed this twice successfully to fit 2 different machines.

... vertical space. I used 6 pieces total. Remixed from: https://www.thingiverse.com/thing:4643756 Print Settings Printer: Snapmaker 2.0 A350 Rafts: No Supports: No Resolution: 200 Infill: 15% Filament: eSun PLA+ Black Category: 3D Printer Accessories

... vertical space. I used 6 pieces total. Remixed from: https://www.thingiverse.com/thing:4643756 Print Settings Printer: Snapmaker 2.0 A350 Rafts: No Supports: No Resolution: 200 Infill: 15% Filament: eSun PLA+ Black Category: 3D Printer Accessories

Designed in Tinkercad for Snapmaker A350 Enclosure.

This was printed on a Snapmaker 2.0 A350 using Luban. PLA Quality - Normal Quality (Luban). This print doesn't need any special settings. There is an inner ring that has been designed to be sanded (if required). Make sure you clean out the cap...

I designed these to use with my Snapmaker 2 A350 and Enclosure. I will be venting the enclosure using the supplied exhaust hose thru a partially opened window in my office. I will be mounting on 1/8" masonite or particle board to seal the window. ...

This is a collection of parts I designed for my Snapmaker 2.0 A350 enclosure. The enclosure measures 820x620x600, fabricated from 20x20mm pine, with wall panels made from 9mm plywood and a door constructed from 4mm polycarbonate. Additional optional...

I needed a mount for my Wyze Cam v3 to attach to my Snapmaker 2.0 A350, and found these other 2 things. I took the cam mount from cdoucet57 and connected to the the base from da96jdm. ... cdoucet57: https://www.thingiverse.com/thing:4938173 ...

This is a print of the wire clips used in the Snapmaker 2.0 A350 enclosure used to hold the led wires on the enclosure. I needed a few more so I created these with Tinkercad. Tested on the A350 enclosure, but should work on the other sizes. ... You...

... set is designed to clamp 4 coasters with Ø110. ... Every center of the coaster is 125mm out of a certain axis. eg. One center is at X-125mm, Y125mm. The center of the middle fixture-'star' is 0,0 coordinater for your laser-setup on the SnapMaker A350

English below Support pour échange rapide du plateau Laser de la SnapMaker 2.0 A350. Il faut imprimer 2 plaques J’ai utilisé 4 aimants de Diamètre 15mm et d’épaisseur 4mm. 8 Noyaux M4x4x6 8 Vis M4x6 Temps 10h55mn Chaque Plaque Holder for quick...

Rewind spool holder for Snapmaker 2 A250 / A350. Designed to accommodate spools of inner diameter 45-90mm perfectly. A stiff spring provides sufficient tension for approximately 1.5-2 turns, ensuring a reliable rewind experience. To further enhance...

Customized my go-to Raspberry Pi 3 B enclosure to perfectly fit on both my Snapmaker 2.0 A350 and the classic Snapmaker, now seamlessly integrating with all my devices running OctoPi.

This is a frame to fit the snapmaker 2.0 enclosure hole for the display. the hole for the display in the door is much bigger that the actual display, så laser lights is visible and could harm kids, animals, etc. this frame fits in the hole and...

... ...These are to give you a definite, repeatable origin for use with the CNC. You can combine them with my fence to help contain dust on the work surface for later cleanup. I've included the models, and a gcode file to print them on the A350 out of PLA.

The moveable element has been designed such that it will allow you to use the rubber plugs that comes with the Snapmaker to secure it to the laser bed. ... I will hopefully amend this design in the future to allow holding down items that bow or lift...

I received my Snapmaker 2.0 A350 enclosure a week ago after having my printer for 8 months. Since getting the printer I've been using Octopi to control and monitor the printer. I couldn't figure out a good place to locate the octopi so I fired up...

Plate for sliding door to close & open the LCD on Snapmaker A350 Enclosure.

SETTINGS: Manufactured by the Snapmaker 2.0 A350 Printer Layer Height: 2.5 millimeters Printing Velocity: 300 millimeters per minute Rapid Movement Speed: 800 millimeters per minute Z-Axis Step Size: 0.5 millimeters Estimated Printing Time:...

Here is a stand/mount for the Wyze Cam Pan for the Snapmaker 2.0 A350 with Enclosure. Designed it myself and it turned out pretty good for my use. I have it mounted on the bottom left extrusion with T nuts (still have to find some t nuts that fit...

This enclosure is designed to contain and protect loose cabling on the underside of the Snapmaker 2.0 A350. By using the natural "ribbing" found on the underside of the mounting plate, an enclosed cavity is formed to house the loose cabling routed...

I just bought a SnapMaker A350 and wanted to use my Mosaic Palette 2 Pro. Didn't find my clip that came with my Palette. So I decide to create one. It fit perfectly the A350 with the PTFE tube that came with Palette 2Pro. Can be use with or...

Square for positioning plate on Snapmaker A350. ...I made this model to easily get consistent quality when engraving a alluminium plate.

Stand for filament dryer to fit Snapmaker A350 with enclosure This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/75Dv9wCa76n

Wyze Camera Perch that mounts to Snapmaker A350 enclosure. Hole to run cable through. Pocket to drop in the wyze camera magnet for an even stronger hold. ...Can be mounted low as shown or high in the upper corner.

I just recently purchased the SnapMaker 2.0 A350 and wanted to run a few test to optimize some engraving settings before diving into any long intricate projects. I decided to run some tests on the dot density setting first, my goal is to use the...

The purpose of this manual is to solve the following problems of the Snapmaker A350: a) Uneven printing surface b) Fluttering of the printing surface when changing the direction of the Y-axis c) hooking of the sensor and shifting of the printing...

The purpose of this manual is to solve the following problems of the Snapmaker A350: a) Uneven printing surface b) Fluttering of the printing surface when changing the direction of the Y-axis c) hooking of the sensor and shifting of the printing...

Used with an A350, it will likely work with smaller versions of the SnapMaker 2 as well. This modification solves the issue of filament coming off the reel when the machine moves to home position. Default setup is for a small spool with a 32mm...