snapmaker a350 enclosure 3d models

Wyze Camera Perch that mounts to Snapmaker A350 enclosure. Hole to run cable through. Pocket to drop in the wyze camera magnet for an even stronger hold. ...Can be mounted low as shown or high in the upper corner.

Stand for filament dryer to fit Snapmaker A350 with enclosure This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/75Dv9wCa76n

This is a frame to fit the snapmaker 2.0 enclosure hole for the display. the hole for the display in the door is much bigger that the actual display, så laser lights is visible and could harm kids, animals, etc. this frame fits in the hole and...

Tool to support the enclosure cable from CPU to the enclosure. ...The logs are great enough for the connectors.

This design is to compensate for the small space available when the printed bed is all the way back in the A350 Enclosure. Tip: Snap the chain link closures in place with a pliers. If the printer is already in the enclosure, first fit the support...

This design is to compensate for the small space available when the printed bed is all the way back in the A350 Enclosure. Tip: Snap the chain link closures in place with a pliers. If the printer is already in the enclosure, first fit the support...

Could not find any enclosure mounts for a Wyze cam and the Snapmaker A350 enclosure so decided to create a remix for my first time. Remix designed off of Design8Studio's remix to be used with a Wyze Cam and mounted to the Snapmaker A350 enclosure.

it s the cover for this https://www.thingiverse.com/thing:4746812

I needed a 90deg diverter for the exhaust vent on the enclosure. Uses the existing port screwed into this diverter. ... Additional Parts: M4 x 8mm (used 4 of these to secure existing exhaust port)

In my case, I needed a hole on top in my Snapmaker 2.0 A350 enclosure. After some time, I needed to arrange a PTFE connector for the convenience and reliability of filament feeding. The result is a simple, reliable and convenient solution. Later I...

Designed in Tinkercad for Snapmaker A350 Enclosure.

Plate for sliding door to close & open the LCD on Snapmaker A350 Enclosure.

This is designed for the Snapmaker 2.0 A350 with enclosure. The FreeCAD file is included for easy modification.</p><p>Tested with initial layer height 0.3mm and general layer height 0.25mm. ...Used Snapmaker Luban profile "normal quality" as...

This is designed for the Snapmaker 2.0 A350 with enclosure. The FreeCAD file is included for easy modification. Tested with initial layer height 0.3mm and general layer height 0.25mm. Used Snapmaker Luban profile "normal quality" as template. ... ...

Snapmaker 2.0 A350 Enclosure Touchscreen Mount - Base of mount can move along the enclosure rails - Mount can spin 360 degrees through the use of a bearing Amazon components: 1) Brass Knurled Nuts Threaded (M4) -...

I have redrawn the design and adapted it to fit the enclosure of a Snapmaker 2.0 A350. ... Ideal when the Snapmaker is placed against a wall, to hold the spool on top of the enclosure.

This is a dust cover to protect the exhaust fan on the Snapmaker 2.0 A350 Enclosure. ... I realized that when I started CNC milling, that I didn't want the dust to clog up my fan, so I created this cover with removable plate to protect the fan when...

This is to cover the opening normally reserved for the Snapmaker 2.0 touchscreen in the A350 enclosure. I sometimes want the touchscreen fixed on the original mount so that I can monitor the progress via the camera I have mounted to watch for...

Snapmaker 2.0 A350 Enclosure T Door Handles (2x) • Designed originally in Fusion360 (attached) • .jsons & .gcode for print settings (attached) • Contains two versions, one regular T handle and a second version with a small nub/extension to loop cord...

Two version of sliding door handle for Snapmaker 2.0 A350 enclosure - version for two M3 screws (I used 2x M3x20 screws - sufficient strength for PLA) and version without screws (not to use PLA - very fragile. ASA/PETG/etc is better). ...The rigidity...

Two version of sliding door handle for Snapmaker 2.0 A350 enclosure - version for two M3 screws (I used 2x M3x20 screws - sufficient strength for PLA) and version without screws (not to use PLA - very fragile. ASA/PETG/etc is better). The rigidity...

Designed for Snapmaker 2.0 A350 with enclosure to solve the problem of the filament jumping over to the "wrong side" of the Z-tower and getting stuck there. Rather than holding the filament, this filament guide addresses the direct problem of...

V2 has more holes (to save material), as well as I have shaved down the rear ridge and also elongated the main mounting holes to allow for a little bit of play when using the included M4 x 30mm bolts that come with the Snapmaker 2.0 A350. ...This design...

This design is to mount the Snapmaker 2.0 A350 External Power Supply to the outside of the rear plexiglass panel just above the grommeted pass-through just above the exhaust duct. This allows for easy location of the power switch as well as the...

I (unfortunately) made my custom enclosure to the same size as the Snapmaker enclosure, which means there's no "good place" to mount the camera to the bed so your item doesn't move in frame, if you mount it at the front of the bed, when you move the...

Plates PVC foam plate 13 mmHard ware FATHSome parts you can print with your snapmaker

Movable (T-Rail) holder for instruments and calibration cards. As is always the case, calibration cards are not easy to find exactly at the rare right moment)) Now, they are always on hand with the tool. Printed from wonderful...

This is a remix of Rocinante2's [Wyze Camera Mount for the A350 enclosure](https://www.thingiverse.com/thing:5234172). I slotted the bottom hole so that it would also fit onto the threaded holes in the A250 T-slots, which are apparently a little bit...

ONLY for the SnapMaker 2.0 A350 Enclosure. I do not know if it fits others. 3 piece assembly so that the SnapMaker 2.0 A350 control pad is easily visible from the side. My 3D printer table setup has the longer side door panels facing me so the...

This is a control panel enclosure for A350. It helps in few ways, protects screen, blocks light, and allows mounting of control panel else where. ...Takes just under 7 hours to print the door with a raft, sorry dont have timings for the main enclosure.