snapmaker a350 enclosure 3d models

<p>I had to find a system to keep my aeration tube on the ceiling of my basement. ...I fixed myself on existing cable passes.</p>

This adjustment block is used to raise or lower the X-axis a little bit on the left and right at the screw-on points in relation to the table height (plus/minus 0.25 mm) in order to eliminate precision problems caused by the manufacturer.

My aeration tube was slightly too short to connect to my ventilation outlet. ...So I modeled a junction so that I could assemble two tubes together.

This adjustment block is used to raise or lower the X-axis a little bit on the left and right at the screw-on points in relation to the table height (plus/minus 0.25 mm) in order to eliminate precision problems caused by the manufacturer. ...

The Creatility glass has rounded corners, and this is a remix that works with square glass without rounded corners. Print each part twice. It's still for the 31x31x4 cm glass. You would need 6 part in total. - glass_bed_clamp_middle.stl (middle...

Test to see if you printer will suffer from overhang curl. ... I could only avoid it by using 0.1mm layer height and z-hop

<p>Author : <a href="https://www.thingiverse.com/rojaljelly">rojaljelly</a></p><p><a href="https://www.thingiverse.com/thing:4365295">https://www.thingiverse.com/thing:4365295</a></p><p>Thank to <a...

You can find this item on Printables here: https://www.printables.com/model/153187-snapmaker-20-module-head-mount-for-enclosure This is a mount to hold 2x spare module heads and spare accessories that slots onto the side of the enclosure for an A250...

Here is a stand/mount for the Wyze Cam Pan for the Snapmaker 2.0 A350 with Enclosure. Designed it myself and it turned out pretty good for my use. I have it mounted on the bottom left extrusion with T nuts (still have to find some t nuts that fit...

Rremove panel handle

Hang this box on your Snapmaker 2.0 Enclosure and put the unused toohead in. ...The box can be installed onto the 48CA beams only.

This is a mount to hold 2x spare module heads and spare accessories that slots onto the side of the enclosure for an A250 or A350 Snapmaker. The one photographed features an extra pocket on the side for other accessories but I've uploaded another...

Wanted a permanent mount spot for a cam in my Snapmaker 2 / 350 enclosure. Since I'm using Ubiquiti Protect and a cam (Flex G3) was at hand... easy choice. Mounts with a small M4 bolt in an existing enclosure tap/hole. ...Design allows for moving mount...

Adjusts the position of the spool on the enclosure of the Snapmaker 2.0 A150 by lifting the spoolholder bracket vertically by 90mm. This allows spools up to approx 300mm or 12inches in diameter to be mounted above the printer, ideal for a more...

... a bit of post printing work to complete the product. This vent is designed to work with the "Snapmaker 2, Enclosure, Modular Trickle Vent Exhaust, Pipe Connection", provided in my collection. PLEASE READ ALL notes before proceeding. ...

Ich habe eine einfache Halterung für die V1 Beaglecam erstellt, um sie am Gehäuse des Snapmaker 2.0 zu fixieren. Es werden nur zwei Schrauben M4x15mm benötigt, die Löcher mit Gewinde M4 sind schon am Gehäuse vorhanden.. Der Lochabstand 40mm. Only...

This part is designed to guide the filament inside the Snapmaker 2.0 enclosure (probably works in the SM original too), to prevent that line to get stuck on the linear module's end. ... I prefered not to use screws (I did not have) and not to alter the...

AboutI wanted to be able to conveniently place my Snapmaker's display on top of the enclosure and turned to the side, however wanted to keep it easy to move back to the enclosure and up again. ...So I've created this magnetic mount design that can slide...

I wanted to store my Palette Pro 2s on top of my Snapmaker enclosure and utilize a proper PTFE guiding system. I could not find anything that fit my setup so is designed this to match my setup. On my rail I have another one, in case I am storing a...

A slimline 90 degree exhaust vent to connect the supplied 3 inch ducting to.I suspect it will fit all snapmaker enclosures as long as they have the same 3 inch ducting. Hole centres mean that it will also fit directly on to an 80mm fan although the...

Needed to quickly extend my 3 inch ducting from my snapmaker a250 enclosure to point it out of the window via some cheap ebay 3 inch ducting.The walls are kind of thin so dont dont overtighten any clips you may use. I was in a rush so excuse the...

With this Add-on you can store some things on top of your Snapmaker without having fear of breaking the top section of your snapmaker.

easy and useful multiple spool holder for snapmaker 2.0 A350T, you need a 10mm steel rod

... IF YOU WANT. If you need to make holes in the enclosure like the pictures, you can download the bowden mounts by LeelllWill: https://www.thingiverse.com/thing:3230377 Bowden Y-splitter by Jpasternack https://www.thingiverse.com/thing:2867089

not sure its needed really but anyway.I was going to upgrade and properly smooth the curve but actually I think I prefer it how it is.A terrible dark video to show how to fit and how it looks/works is included...

This is a connector to fit the standard issue Snapmaker 2 exhaust pipe, and connect it to the modular trickle vent exhaust system I have designed. ...(following soon)

This part is a remix of a A350 part to make it if in a A250 where a) The rear part is split in two with a lock mechanism and can be printed in A250 b) Holes are displaced as the original part obstructs the case cable hole in an A250

In the A250 with Enclosure, the original Y axis adapter makes the cable chain hit the back of the enclosure, no matter the length of the chain. ...This part shortens 10mm the original part and with 14 links + ends you can cover the whole Y axis movement...

I wanted a spool holder for inside the enclosure and re-use the existing one. This attaches to the holes in the 24x24 side beam (2 x M4x15 screws) and puts the spool at a 30° angle. The bearing is something I found and fits directly onto the old...