snes case raspberry pi 3 3d models

And connected a power wire from the PSU to a LM2596 to get 5V to power the Pi directly from its GPIO pins. So I don't need to run any cable (except for the camera) outside the case. The top cover is separated, so future mods can be done easily. ...I am...

I was browsing through Pi Cases and noticed that most of them were just a standard box with cookie-cutter styles. I decided I wanted to create something truly unique. As a huge fan of Mid Century designs, I set out to craft an interesting take on a...

Modified for use with hardware: Installed 4x McMaster-Carr 91292A019 from Pi-BOT side: 18-8 Stainless Steel Socket Head Screw M2.5 x 0.45 mm Thread, 20 mm Long Installed 4x McMaster-Carr 94180A321 on Pi-TOP: Tapered Heat-Set Inserts for Plastic...

A fresh spin on my previous Pi case design. I've created a completely screwless case, minus the fan attachment, by attaching it directly to my vesa mount bracket. To accomplish this, I designed a simple hang bracket that eliminates the need for...

NES Bottom: I downsized the supports to fit snugly around the Pi 3 so that none of the chips would rest on them. Additionally, I incorporated an LED hole and a mount for the LED. A 3mm LED fits perfectly in the mount and can be secured with glue. To...

...The Pi itself is clamped together between the top and bottom case. 2. The top part of the case comes in three different versions: - Plain, with no extra features. - With a hole for a 40mm fan. - With a hole for a 40mm fan plus a power button.

To prevent the Pi Zero from moving around excessively when attached with a mini-HDMI adapter, I introduced blocks to hold down the board securely inside the case. To enhance airflow for users who run overclocked boards but still want to maintain the...

I cut out a hole for the IR receiver (for the version of the board with the attached IR receiver) and didn't have any 2.5 mm screws, so I added pins to hold the PI in place and some tabs for friction to hold the case together. I covered the old...

I wanted a mesh case for one of my pi 3b. I made this in tinkercad with super basic knowledge so I apologize if it's a bit rough. I added one option only with 40mm fan and another one with both 40 and 30 mm fan. ...It's not so clean, but it works for...

I wanted a mesh case for one of my pi 3b. I made this in tinkercad with super basic knowledge so I apologize if it's a bit rough. I added one option only with 40mm fan and another one with both 40 and 30 mm fan. ...It's not so clean, but it works for...

The stands need to be glued and put the pi and screen at a 60° angle Print Settings Printer Brand: Ultimaker Printer: S5Rafts: Doesn't Matter Supports: NoResolution: 0.1 Infill: 20 Filament: [ Makerfill PLA...

Fan Mods I used: https://www.thingiverse.com/thing:4549738 https://www.thingiverse.com/thing:4548187 Camera Case I used: https://www.thingiverse.com/thing:2987719 I soldered the USB2.0 D+ and D- directly on the controller board, as well as on my...

Without the block the Pi Zero kept moving around with the weight of the mini-HDMI adapter attached to it. I added a case top with a cut-out zero logo to help with air flow for anyone that runs an overclocked board but doesn't want the gap for the IO...

Box designed to house a rpi 3, skr 1.4 and voltage converters. ... You will need M3x10 screws for the cover and the standard ones to screw the screen to the case.

I wanted to use this case design for my ender 3 but wanted it to stay in place but also be easily removeable if needed so I created this thin but solid mount holder that attaches to the printer at just the right distance from the USB port for a short...

This case is designed for the [Waveshare TFT 3.5](https://www.waveshare.com/wiki/3.5inch_RPi_LCD_(A)) screen, because many cheap clones on Aliexpress have the same layout ([mine](https://www.aliexpress.com/item/33041327727.html) is also a clone). ...

Really needed a great enclosure for my Raspberry Pi, that would also accommodate a 2.5" hard drive and a USB hub. So, I designed this using parts i found on Thingiverse. Credit goes to Lilykill for the Fallout Mini-nuke:...

Wanted to use an old Pi3 with a 2.8 TFT (adafruit clone) to monitor the camera of the UM S3. The case fits the Pi3 and also has some supports so that the screen does not sag. The stands need to be glued and put the pi and screen at a 60° angle Print...

Wanted to use an old Pi3 with a 2.8 TFT (adafruit clone) to monitor the camera of the UM S3. The case fits the Pi3 and also has some supports so that the screen does not sag. The stands need to be glued and put the pi and screen at a 60° angle Print...

Remix of this to fit a Pi 5's slightly different IO. My modelling skills are weak, tolerances could be better, etc etc. ...But it works.

Through some trial and error I came up with this: a clean case for the RPI 3 that is tall enough for a heatsink and has the fan inside, not mounted on the outside. The design is still work in progress, so please be kind and feel free to point out...

Based on the excellent Adafruit design, this case has been enhanced and elevated to accommodate a 3.5" touch screen comfortably. The photo I'm sharing shows mine, sourced from China via eBay. This case is straightforward, allowing you to make...

Remixed from https://www.thingiverse.com/thing:4192636 to place the Pi on its side so as to take up less space. Also removed some of the port holes next to the power cable. ... Re-mixed in TinkerCad.

Heya! ... Just a modification for a 30mm fan in the amazing case from Malolo. Original case: https://www.thingiverse.com/thing:3719217 Happy Printing!

... structural integrity. ... Added holes for PoE pins and taller CPU heatsink. Deleted bracket by USB and Ethernet ports. Please download the original baseplate [here](https://www.thingiverse.com/thing:559858/files) labeled as boite_raspberry.stl

I adjusted the number of ports available, also lowered the PI location so that I could add a mount for the fan. I also added posts for a Buck Converter. **Note: I have not printed this yet, and its a work in progress. ...Print at your own risk**

... 2 braces, on the left side, where there is a hole for USB and Ethernet ports. This is to help prevent warping. They can easily be cut off after print is finished. Use two (2.5 x 20) screws to secure Raspberry + Bottom and Top parts  

Conçu pour le boitier original du Raspberry, ce support est pour un ventilateur de 3cm qui rentre légèrement en force pas besoin de le visser et le support lui est collé par des petits morceaux de double-face dans les angles. Pour avoir la bonne...

The Case Unfolds: Camera Insertion Sets Stage for Action. Camera Placement: Operator Places Device Within Housing Unit. ... Snap Closure Confirmed: Protective Cover Secures with a Satisfying Click.

Dimensions: 144 x 154 x 27 mm I wanted a Pi and a HDD in one enclosure, but I couldn't find one that met my needs, so I decided to build my own. Others may have done it before, but initially, I envisioned including a fan. To accommodate an 9.5mm HDD...