snes controller case 3d models

Make use of microbit gyro for controller

I attached the Snappy v3 leg to the case for a RepRapDiscount Smart Controller LCD Display. The Snappy v3 assembly instructions don't provide guidance on LCD placement, but from what I can see, this replaces one of the "Support Legs" on the Z-Axis...

This is an upgrade of wifapaj's EVO Flight-Controller Case. It is designed for the SPRacing F3 EVO flight controller stacked on top of the SPRacing OSD/PDB board. Wifapaj's lid fits perfectly and can be held in place with M3x30 screws. Height is...

The reset button knob on my RepRapDiscount Smart Controller by prodimensional was too short, so I extended the button a bit. Now I can easily press the reset button. The pins of the front cover were too thin and snapped off. To fix this issue, I...

These are custom clips that I designed specifically for the Case for Reprapdiscount Smart LCD Controller XXL Created by wersy which can be found at http://www.thingiverse.com/thing:79820/#remixes I thoroughly enjoyed everything about the original...

I designed and created several components to securely attach pablogil's 3DR - RepRapDiscount Full Graphic Smart Controller case (available on Thingiverse at http://www.thingiverse.com/thing:213852) to the side of my MendelMax 1.5 printer. The parts...

This is a custom add-on for the popular "Case for the Full Graphic Smart LCD Controller" design by wersy, available at http://www.thingiverse.com/thing:87250. I'm a big fan of this design and have been using it as a handheld device, but I wanted to...

To add a potentiometer to control the backlight brightness do the following: Desolder the smd restistor called RBL Drill three small holes as shown in the photo (I used a 0.9 mm bit make sure not to drill through the nearby tracks) Insert the 10...

Case designed specifically for the xEM Access Controller v2, featuring a cover plate to protect the antenna.\r\n\r\nThe holes in this design are crafted to accommodate m3 bolts, although some may require minor adjustments for through-hole...

This is a Heatsink Controller Case for iPhone XS Max with PUBG on the back, featuring a carbon fiber effect when printed at 0.2mm layer height. This is the updated version I created after refining my design based on the initial print and...

LCD controller used to control 2 parameters. This is a remix of a grabCad file. ...

This case is crafted to cradle the PCB from an xEM access controller with precision. The two components click seamlessly into place after printing, requiring a gentle yet firm push to secure them in position. I'm confident that my design has reached...

The instructions for printing this case are relatively simple: Instructions: This case can be printed using standard settings or modified ones; I achieved excellent results with the following parameters: 20% Infill rate 5 Top layers for a smooth...

A custom controller case for the Original Snapmaker 1.0 adapted to fit any 40mm noiseless fan, replacing the always on small and loud fan in order to reduce noise. Printed in 3 parts which snap fit together is attached using the same screws from the...

Another spacer is included for cases where the X-axis motor lacks sufficient clearance to pass through the case. This was an issue encountered during the design process, specifically with the Tarantula printer. To resolve this, the case can be...

I love the RepRapDiscount Full Graphic Smart Controller Case by mightynozzle. I can move my control LCD screen around as I like, but I also like it to be solidly fixed on my enclosure when I want it tidy. So I designed this! You can put it wherever...

One of the bottom holes should be partially closed with 2-3 layers, easily removable if needed.\nThis is an ongoing "Under Construction" remix of a case originally designed for Rumba.\nFull Graphic Smart Controller -...

There is a good explanation of this controller at:

Simple case for the Storm32 Gimbal Controller. Please upload a picture of your make. ------------------------------------------------------- This design is not intended for commercial use or resale. Want this part? Just write: Facebook:...

This is a Flight Controller case: For the F3 Flycolor Raptor S-Tower 30A or other FC with the same structure: To print this 3D model, you will need: 8 or 12 M3 threaded spacers (nylon/plastic recommended). 4 M3 nuts (nylon/plastic recommended). 4...

Power is provided by a micro-USB breakout available here: - https://www.aliexpress.com/item/4000385426649.html - https://www.aliexpress.com/item/33057915333.html (lote 5 pieces) For software, I am using WLED (https://github.com/Aircoookie/WLED),...

I went with the RepRap Full Graphics Smart Controller. Printed the case here: http://www.thingiverse.com/thing:87250 Unfortunately I needed to mount it, so I designed this bracket to clip on the top. Print two, each one will screw into the bottom...

Case for widely used graphics display with light switch.

... the other three are yellow and located at the bottom. There's also a hidden USB port on one side, and a power-off button for the controller. ...In the center, there is a small screen displaying the temperature as well as other essential information.

You need to enter the length and width of the PCB of your controller board, and the offset from the board edge to the mounting holes. There are two more parameters which are optional - top gap - which adds extra spacing between the PCB and the top...

The variables to examine for modification for the graphics controller are primarily: G_Y_Offset Br_Ht_Add = 10; //I have this set to 0 for the LCD2004 Any of the variables with the prefix G_ are related to this. Since I don't possess one of these...

I build a strong argument to support my Geeetech COM full-graphics Smart Controller Board.

Controller Unit for High-Power 80 Watt Pulse Width Modulation (PWM) Electric Motor Speed Management System

It works seamlessly with the T.VST56 LCD Controller Driver Board purchased from Ebay.

Prusa-inspired housing designed specifically for the KFB2.0 controller board and 40 millimeter fan setup.