snes controller case 3d models

Since no suitable case was available for my flight controller and receiver combo, I created this custom solution myself. I am utilizing the following hardware:\r\n\r\n- Micro Betaflight Omnibus STM32F4 F4 Flight Controller (27x27mm)\r\n- Frsky XSR-E...

These controllers are hazardous without a casing as the board's sensitive components sit at mains voltage. The lid snaps on and the PCB slides into place after removing the small metal bracket supporting the potentiometer. The design includes plenty...

A custom mashup of two Thingiverse projects: Case for the Full Graphic Smart LCD Controller and 20mm V-Slot Mounting Bracket for Full Graphic Smart LCD Controller. This remix includes just the bottom part of the case and the brackets, directing users...

Compact case for aliexpress pwm controller ( https://a.aliexpress.com/_9A8Ck9 ) with soldered off connectors (permanent installation) The case features snap on cover, nice pcb fit with mandatory cutouts for the knob, in/out wires and status led (if...

Instead of ventilation the case back has a "foot" that acts as a heat pipe and the entire back case is the heat sink. It is intended that the back case be milled from aluminum. There is a hole for a barrel jack connector for power, a hole for a...

I created this arcade controller custom case because I needed a controller that's large enough to rest your left and right hand on while playing and can be printed using a standard-sized printer with a maximum bed size of 20x20cm. Despite the...

The lower portion of the casing has a built-in support designed to hold the Controller at a 45-degree angle securely. To utilize the bottom casing effectively, you can pair it with the top design provided by Tig29. The base of the case now...

Relevant hardware used in this case includes: The RUMBA mainboard from RepRap, and the RepRap Discount Full Graphic Smart Controller. ...More details on these components can be found at the RepRap wiki under the given references:...

I remixed MyStoopidStuff's case to make all of the holes self threading into the plastic for M3 bolts, a smaller hole for the power outlet to match the ones I had, and an extra hole for a 100k pot that I wired in parallel with the 50k thermistor for...

Case for LILYGO® TTGO VGA32 V1.4 Controlleryou will need theLILYGO® TTGO VGA32 V1.4...

I wanted a straightforward method to mount my Ramps case with full graphic smart controller on my Mpcnc. So I created this plate to fit GoPro mount systems seamlessly. Now, I can utilize any GoPro support to mount my ramps case without any hassle!

The Raspberry Pi connects directly to the LCD, making this a protective case for both devices. Exposed openings provide access to the USB, network ports on the Raspberry Pi, along with holes for HDMI connections. The package also includes a bracket...

This is a holder for the "Case for the Full Graphic Smart LCD Controller" (http://www.thingiverse.com/thing:87250) by wersy. I like this design and use it as a handheld. But I also want to be able to store it easily. So, I made this addition - a...

It was designed in Fusion360, and my goal was to craft a custom holder that would snugly fit both the DJI Mavic Mini controller and an iPhone X housed within a Mous case. The design includes a magnetic mouse pad attachment to keep everything...

Do Your Own SNES Mini Before It Hits The Shelves!!

Game Holder for Super Nintendo Entertainment System (SNES) Cartridges!

The reset button knob of Case for RepRapDiscount Smart Controller by prodimensional was too short for my china RepRapDiscount Smart Controller, so I lengthened the button. Now I'm able to press the reset button successfully. The pins of the front...

This is a case designed to connect a HAKKO style T12 digital soldering iron controller to Milwaukee M18 batteries. I designed it all in FreeCAD, and made an attempt to style the case similar to other Milwaukee M18 devices. Versions with and without...

To prevent unwanted movement, I generally adhere controllers with foam tape even when housed within a case like this. As I update it to provide better stability over time, you might need to drill holes and screw it down at the corners if desired. I...

Simple case for the Storm32 Gimbal Controller. Please upload a photo of your make. This design is not for commercial use or selling! Du möchtest dieses Teil haben? Schreib einfach:<br/> Facebook: <a...

Sainsmart/geeetech.com full graphic smart controller board. This board is similar to the other graphic LCDs available but the physical layout is a little different. This case allows for screw mounting of the board and is designed to sit on a desk.

A simple case with mounting holes (on a horizontal surface) for the cheap PWM LED dimmer /motor speed controller 5A 30V 90W from Aliexpress (https://www.aliexpress.com/item/1005002093051084.html). Prints without supports. Also a version for 2...

This case is designed for the Full Graphic Smart LCD Controller available at http://www.reprapdiscount.com/home/34-full-graphic-smart-lcd-controller.html. Like my other enclosures (http://www.thingiverse.com/thing:35438 and...

I tried to print the original one by deBaer but I had a couple of issues.All the parts are the same as deBaer's except the controller case.I used M2 6mm screws for the screen, might wanna get better quality ones instead of the cheapest like I did...

The design includes modules for the front case, back case, knob, and two buttons, one of which is the shorter emergency stop button. Initially, I struggled with the original dimensions because I believe that PLA shrinks when cooled down, so make...

... have 4 interference fit holes for 8-32 screws to thread in securely. The 8-32" x 7/8" screws should slide through part 2 and the vex match controller, then thread into part 1, joining the top and bottom halves of the case together (see pictures).

More Info on RickMote Controller: GitHub - Bishop Fox - rickmote Bishop Fox - Blog - The Rickmote Controller: Hacking One Chromecast at a Time - 16July2014 YouTube - Rickmote Controller - Hijacking TVs via Google Chromecast - 15July2014 YouTube -...

I recommend holding the device sideways, with the buttons facing up and pushing the controller out using the opening for the buttons whilst pulling the case in the opposite direction. The device comes out pretty easily this way, should you need to...

Introducing a customized swivel clamp case crafted specifically for Hobby King KK 2.0 multirotor flight controller board (XL-RCP7.0). This innovative design includes three components: the base, main case, and lid. Designed with ease of maintenance in...

ASSEMBLY: - Part 2 should have 4 clearance holes for 8-32 screws - Part 1 should have 4 interference fit holes for 8-32 screws to thread in The 8-32" x 7/8" screws should slide through part 2 and the vex match controller, then thread into part 1,...