snowboard binding 3d models
6072 3d models found related to snowboard binding.
thingiverse
This clip is designed to hold together papers securely, accommodating anywhere from 3 to 26 sheets at once. Currently measuring 70 mm in length, it can be scaled up or down as needed. To fit the entire long side of a US Letter sheet, scale it to 11.5...
cults3d
For bookbinding and scrapbooking. Kit composed of 2 squares of 180mmx70mm and 20mm and 15mm width, a T and a straight ruler in 5mm, to make the necessary separations, a corner cutter. ... This kit is oriented to scrapbooking, has the perfect measures...
cults3d
Measurements: 21.5 cm long 5 cm wide 3 cm high Distance between holes: 1 cm contains wedge and base stl files
cults3d
basic kit for bookbinding 3 mm gap at the corner cutter, 2 cm gap at the sides and 1.5 cm gap at the crease.
thingiverse
------------------------- Snowboard Mounts ================ Wall snowboard mounts designed to accommodate gloves and helmet. Snowboards should be placed on the mounts toe side to the wall (as heel side usually extends further out from the board). I...
cults3d
An ear-friendly clip for your ski or snowboard helmet. ...It makes wearing a mask while skiing or snowboarding a lot more comfortable!
thingiverse
The button is intended to fit inside the front of the ski bindings (where the toe of the boot goes) and the other ski is held up by interlocking the brakes, as shown in the photos. I included an extended version that will hold a snowboard too. The...
thingiverse
Stomp pad for snowboard, you can change the size based on your own preferences.
thingiverse
Locking plate for Salomon Kiana snowboard boot. ... Note the different left and right plates.
thingiverse
This is a snowboard rack that spreads out the positive energy hand.
myminifactory
Watch the Demo Build here: https://youtu.be/WGEDDWCxds0 Use this snowboard fixture to display your board in the vertical position, nearly flat against the wall, bindings out. Both screws mount into the same stud in the wall, spaced vertically, no...
thingiverse
hook to easy wear/unwear medic mask when using ski/snowboard helmet. Stripe 15 mm wide... ...(K2, Salomon, ....)
thingiverse
... I-beam. ... snowboard rest on bottom inside of the ibeam. the hook on the clip goes over the snowboard in neutral position, to unhook, flex the mount upward to release snowboard. ... printed using PETG, infill 80%, brim 4mm, tree support everywhere.
grabcad
M10 Battery Cable Connector Binding Post - Black
thingiverse
Ski Bike, Snowboard Bike, Axle Adapters (Pictures are just reference) To convert an old bike and old set of skis or a snowboard into a ski bike or snowboard bike, simply bolt adapters to the skis or board. Drive a bolt through the axle, and you're...
thingiverse
Snowboarding stomper used by rebels to evade British Empire marines. Successfully printed with 100% infill, tested in both PETG and ABS plastics. Works flawlessly every time, even when dodging authorities on the next island. ...Huzzah!
thingiverse
SNOWBOARD VICE ==================== This is a Remix of 0161design design wich is a remix of 4numen design of a Snowboard Vice. __Parts needed:__ --------------------- - two M10x100 screws (or something around that length) - two M10 Nuts...
thingiverse
The Burton Imperial Snowboard Boots Shoelace Lock is designed to secure your boots tightly on the board, preventing them from coming loose during high-speed turns or jumps. ...The lock's adjustable strap fits snugly around the boot's lacing system,...
thingiverse
This is a hook designed to make putting on and taking off your mask easier while wearing a ski/snowboard helmet. It fits helmet straps with a width of up to 16mm. ... The CAD file for Siemens Solid Edge can be found in the Thing Files section if you...
prusaprinters
A printable protector for your vehicle, so you can safely lean skis and snowboards against it. Requires 10x4x2 rectangular neodymium magnets (6 per print, and the prints lock together as a pair, so 12 magnets per completed unit). Note: This model was...
cgtrader
Experience a modern snowboard ski goggles 3D model with an old-school and vintage vibe. This premium design is compatible with multiple software, including .max, .fbx, and .obj formats. The ZIP file includes the following models: .max (3dsMax 2016),...
prusaprinters
The stomp pad itself has traction from the lines in the 3, and a height difference between the McLaren logo and the number.I haven't actually tried snowboarding with this, it's a gift for a friend, but I'm hoping it holds up well. ...Planning on...