softrock rx ensemble ii hf receiver 3d models
55167 3d models found related to softrock rx ensemble ii hf receiver.myminifactory
This is an enclosure box for the SoftRock RX Ensemble II HF Receiver SDR radio by Five Dash Inc. https://fivedash.com/ This circuit board has many custom wound coils and transformers that could easily be broken off the board with repeated back and...
thingiverse
This is a case for the Softrock Ensemble RXTX SDR radio that I created. It will also work with the original Peaberry V1,V2, and Omni-SDR SDR radio. The case has built in labels for the ports, vent holes and stand offs for the PCB. The stand offs...
cults3d
Bracket for adapting a Sennheiser HF receiver to your camera. Very simple to install. ...Especially dedicated to Blackmagic URSA mini cameras.
thingiverse
This is great for diversity receivers with two monopole antennas, such as the D4R-II, X4R, R-XSR etc. 3D printing settings: Infill: 100% No support required My S800 build log: https://oscarliang.com/reptile-s800-v2-fpv-wing-build-log/ ...
prusaprinters
Easy to use bracket to keep a MPX receiver RX-7/5 securley in place via a snap-in. ...Additionally a rubber band can be applied keep the snap-in tight.</p>
thingiverse
This is a model of replacement small knob for Yamaha RX-V596 receiver, fits ballance, bass and treble. ...It's fully operational, tested on my Yamaha, but if you want it to look real well then sandpaper it post-print and apply layer of color to fit your...
prusaprinters
This is a enclosure for the Ensemble rx II purchased from http://fivedash.com/ Details of the radio design use can be found on http://www.wb5rvz.org/ensemble_rx_ii Instructions Print a top and case, case screws will hold the PCB in place. Warping can...
prusaprinters
My YAMAHA RX-V479 AV Receiver did not fit into my sideboard. To reduce size, I created a replacement for the 4 feet. ...This gives the receiver much more headroom for cooling while still providing enough space on the bottom for air ventilation and...
thingiverse
This is a enclosure for the Ensemble rx II purchased from http://fivedash.com/ Details of the radio design use can be found on http://www.wb5rvz.org/ensemble_rx_ii Instructions Print a top and case, case screws will hold the PCB in place. Warping can...
thingiverse
Fairly accurate model of the V8FR-II receiver for size accounting purposes.
thingiverse
I recently bought an Lemon RX DSMX PPM 8-channel Receiver + Satellite and Failsafe (http://www.lemon-rx.com/shop/index.php?route=product/product&product_id=118). The receiver board comes sans enclosure (strange, since the satellite comes with an...
thingiverse
First off this was not created by me, I got it from Sketchup Warehouse : https://3dwarehouse.sketchup.com/model/73439e95eaee7960be48f482a56abc37/RX-178-Gundam-Mk-II Credit to : Atherin Model is roughly 18cm tall so not sure what scale this is , as I...
thingiverse
Receiver snaps into the holder and then I use 3M VHB tape to place the holder on my aircraft. ...I'm open for suggestions or improvements Print Settings Printer Brand: SeeMeCNC ...
thingiverse
This is a two part case for the Lemon Rx 6-Channel Reciever (LM0027) I printed both parts with Hatchbox silver Pla on my Monoprice Select Mini. Part 2 needs supports. Once printed, I used a little ca glue to hold them together. Also, you may...
thingiverse
Why did I use the V8R7-II for my receiver rather than an D4R-II ??? Simple... I wanted to wire in transmitter activated LED control, and I also wanted to control the camera tilt in flight with my Taranis. ...(See...
thingiverse
The mount fits a FrSKY V8FR-II case and prints in two parts. a clip for holding the receiver in place and the main body. The design incorporates an integral clamp that locks the Servo connectors in position when the clip is fitted. for security...
thingiverse
A easy way to relocate your receiver closer to the center of the chassis. ...Requires an M3 countersunk screw and double sided servo tape to mount.
thingiverse
# RX and VTX Holder All VTX holder I found for the Martian II didn't quite fit my needs. The antenna cable of the VTX just wasn't long enough to reach the vtx holder. I've also added a RX antenna "tubes" to the holder to stop the antennas from...
thingiverse
9/1/17 Added a short 20mm version of this Com Dock I made this mount similar to other ones I have seen to mount a VTx and Rx at the back of a Martian II frame. ... I printed this in TPU 50% infill.works great
youmagine
Here is a protection In TPU ultimaker (ninjatek) for the receiver Lemon Rx on a chassis 30.5x30.5
cults3d
Here is a protection In TPU ultimaker (ninjatek) for the receiver Lemon Rx on chassis 30.5x30.5
thingiverse
Here is a protection In TPU ultimaker (ninjatek) for the receiver Lemon Rx on a chassis 30.5x30.5
pinshape
Here is a protection In TPU ultimaker (ninjatek) for the receiver Lemon Rx on a chassis 30.5x30.5
cults3d
Here is a protection In TPU ultimaker (ninjatek) for the receiver Lemon Rx on a chassis 30.5x30.5
thingiverse
A receiver cover for the ImmersionRC Vortex 250 and 285 and the FrSky D4R-II receiver. ...Parts needed: 2x 3mm antenna tubes 4x 6mm course thread screws
thingiverse
I liked the idea of https://www.thingiverse.com/thing:2585395 where bowden tube is used to hold RX antennas but I wanted to use it together with VTX antenna pig tail and Matek WS2812B LED/Buzzer. So I designed this little thing. ... - Added the version...
cults3d
A version with and without buzzer Mini receiver furious: Store EU: https://www.drone-fpv-racer.com/furious-mini-rx-frsky-946.html Buzzer 9mm :...
cults3d
A version with and without buzzer Mini receiver furious: EU Store:https://www.drone-fpv-racer.com/furious-mini-rx-frsky-946.html Buzzer 9mm: http :...