softrock rx ensemble ii hf receiver 3d models

this is a receiver box to relocate the stock receiver to the rear of the vehicle. it uses the stock M1.5 hardware. this mounts the receiver where the stock battery tray was. fore use remove the receiver from the stock box. the receiver is then placed...

Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Extended Rafts: Doesn't Matter Supports: No Notes: PLA, .08 This test print was designed to see how well the receiver fits into the mount. The receiver simply slides into place. ...Avoid...

... parts for easy printing: the bottom part, a cover over the PCB, and another cover over the right-angle connector pins. I plan to use most of these receivers with wires soldered directly onto them, so I'll likely create a cover for that purpose too.

there is a version specially for (4-ch) reely receivers an the spektrum ones like srs6000 for example. the screws for the cover should be m3 with lenght about 6-10mm. I printed with TPU - so the box is undestroyable and 97,5 % water- and dust...

To acquire this part, visit: http://apshobbies.com/index.php/store/quadcopter/lemon-sat-receiver-holder-detail Instructions Print using 1.5mm shell with a 25% infill of Bridge Nylon, allowing support touching the build plate during the printing...

vs410 receiver or whatever box that goes in the empty spot (if you're not running a servo winch). ...just a way to tidy up the electronics not waterproof but could be sealed

A compact enclosure specifically designed for the VESC4 motor controller, featuring a dedicated mounting area for the receiver and a separate slot for integrating a Bluetooth module, enabling seamless wireless connectivity and control.

This is a setup that brings together the VRC-3NT USB dongle and a receiver, specifically the FlySky FS-GR3E, for an immersive experience with the VRC-Pro RC-Car simulator on vrcworld.com.

This printable mount is designed specifically for the Futaba R6203SB receiver, allowing you to easily attach it to various surfaces. ...Simply download and print out the template, then securely fasten your device in place with ease.

This receiver mount guarantees a 90° spread of your antennas, and it looks very neat inside your model. Print in PETG to prevent warping in sunny days. ...Add silicone sleeve to the antenna for a tight fit in the print.

This is a case to replace the cardboard on supplied with Frsky G-RX6 receiver makes it easier to fix inside a model aircarft. ...The case is held togeter with clear tape.

A Receiver Mount specifically designed for use with a Futaba R7008SB features holes at the top to accommodate antenna tubes, while a hole at the rear allows for easy attachment of the ext-voltage cable.

I made a stand for my Nyrius BR50 AptX Bluetooth receiver that likely works with the BR40 without AptX and the BR51 with AptX and NFC. It may also work with the BR41 and other similar Bluetooth receivers. To make the feet, I simply cut four little...

The compact RC receiver enclosure is designed to fit snugly into a space measuring 47x32x30mm. ...Secure the device firmly using a combination of double-sided adhesive strips and a gentle yet firm puller for optimal stability.

The CYMA AK Receiver Cover is a sturdy component designed to safeguard the internal mechanisms of the airsoft replica rifle, protecting it from dirt and other external contaminants that could compromise its performance.

This is a Crossfire receiver mount right over the stack well protected all around. ... Printer: Creality Ender 3 v2 Print slov to get the best result I was printing at 15/mms

Mounting the laser receiver in place requires printing both sections, which provides ample protection from damage or harm while positioning it exactly where needed. ...Additionally, a purposeful hole allows easy access to view the LED indicator at all...

On the receiving end, a trailer hitch incorporates a 5/8-inch pin (with 0.005-inch space), situated 2 inches from its outermost tip. ...The design was crafted using Solidworks software in 2016.

Box for Orange Open LRS Receiver Print Settings Printer Brand is RepRap The Printer used is Prusa i3 rework Rafts are not required No supports needed Resolution is set to 0.25 Infill is at 20%

My Wii's reception improved significantly after adjusting the antenna to sit about two millimeters lower, eliminating any interference that caused it to push the receivers out of position.

The provided frame is plain and the tank has been successfully received. ...This means that the structure of the frame is basic, without any additional features or embellishments, while the tank has been safely delivered to its intended destination.

A polar receiver is a device that detects and processes signals from spacecraft in polar orbit, facilitating communication between the satellite and ground stations. ...It plays a crucial role in gathering vital data for scientific research and military...

I reengineered the wallmount clamp with a sturdier receiver and increased its diameter to 14mm, allowing it to securely hold various articulating lamps that often feature obscure block/clamp attachment mechanisms.

The VRC-3NT USB dongle along with its accompanying receiver, such as a FlySky FS-GR3E, is designed for use with the VRC-Pro RC-Car simulation software. ...For more information about this product, visit vrcworld.com.

Pretty basic rack to store the receivers of the XVive U4 and leave space to charge them while in the rack Print in PETG or stronger. ...PLA will eventually break Print upside down so you don't need supports

This custom receiver fits snugly onto the top tube of a Cruzbike S40, specifically engineered to work seamlessly with a threaded insert, ensuring a secure and precise connection for the Steerstopper device.

The central component of a crossbow is referred to as its receiver, which holds the string and assembly for firing projectiles. ...This integral part ensures stability and accuracy during use.

Outer case for the Futaba R2106GF Receiver. ...The case it comes with is a bit flimsy, so this gives it a tough outer shell whilst giving space for the antanna wire, bind button and status LED.

A SolidWorks and STEP file are available for the Spektrum AR6210 2.4GHz receiver. ...For those using SolidWorks, a corresponding .png label is also provided to be kept together with the .prt file.

Can be used ontop of a 20x20 m2 stack.If you want a file with other dimensions feel free to ask :)in the picture its used with a Radiomaster RP1 ELRS receiver.