solder paste dispensing 3d models

SMT Solder Paste Dispenser based on http://www.thingiverse.com/thing:1119914 replace the motor

... than the PCB itself. So, using stencils for every iteration of the board is not very cost effective. That is where solder paste dispensers come in. For more information about the project - https://hackaday.io/project/159401-solder-paste-dispenser

Solder paste dispenser. Solder paste is squeezed out when you push solder paste tube down. Infill 15% is enough except for axis.stl. I suggest use 100% infill there. ... Printed in PETG, but PLA should also work fine.

Solder paste dispenser.Solder paste is squeezed out when you push solder paste tube down.Infill 15% is enough except for axis.stl. ...I suggest use 100% infill there.<br>Printed in PETG, but PLA should also work fine.</p>

Perfect accessory for precision solder paste dispensing Finger-contact point is very close to the point of application Can use 5cc capacity syringe barrels Compatible with a large variety of needles and tips for the highest dispensing precision Ideal...

The design was inspired by the "Spoty precision SMD micro-dot solder paste dispenser" (https://www.avdweb.nl/tech-tips/pcb/solder-paste-dispenser). ... Parts required in addition to the 3-D printed body: * compression spring, 0.75" long, 0.25" OD,...

Inspired from the JBC solder paste dispenser i created this "poor man's" dispenser. You need following parts: -Tuberculin syringe (PZN: 09108383) -Plastic tipp 22 Gauge (https://a.aliexpress.com/_vqYZIi) -M3x30mm screw -M3 Nut & knurled Nut ...

The solder paste dispenser that has a foot switch to free up a hand. Leave part orientation as is. Parts designed to print without support. The [github](https://github.com/koendv/paste_dispenser) contains openscad sources, arduino sources and...

These are the 3D printable parts for my DIY solder paste dispenser design as described here http://letsmakerobots.com/content/solder-paste-dispenser I’ll be selling the PCB over at https://www.tindie.com later if anyone is interested. ... The PCB is now...

These are the 3D printable parts for my DIY solder paste dispenser design as described here http://letsmakerobots.com/content/solder-paste-dispenser I’ll be selling the PCB over at https://www.tindie.com later if anyone is interested. ... The PCB is now...

Control with 32bit processor STM32F103C8T6, OLED display 128x32, DC micromotor 6V / 60 rpm with gearbox.More on this project: https://github.com/Jarins/Solder-Paste-DispenserUpdate: 21/10/2021 Added Screw to SyringePistonUpdate: 22/11/2021 Added...

Two needles - 1mm & 0.5mm for solder paste and flux dispensing. Specially designed for SLA 3D-printing as fast alternative when there are no metal needles at hand. The 0.5mm-needle may not work with viscous paste. ... Solder paste syringe example:...

This tool reduces the force required to dispense solder paste manually. It is also more ergonomic and reduces fatigue. See picture for assembly. The parts "hebel" and "spange" have to be printed twice, one normal and one mirrored each. Requires ...

A long screw for pushing your solder paste or flux out of the syringe https://youtu.be/KWhnIwW-rA0 https://www.youtube.com/watch?v=KWhnIwW-rA0

This is a manual and simple 3D printed syringe dispenser I made with PETG filament. ...

https://www.thingiverse.com/thing:3137757 works fine. ...But for people like me who have managed to damage the dispenser with a pointed object, I have built a small addition.

Arduino Motorized SMT Solder Paste Dispenser

Improved syringe clamp for the Solder Paste Dispenser. ...Designed to fit 10cc Dispensing Syringe Barrels.

This is a clamp to hold down the syringe for Geir's Solder Paste Dispenser posted at Thingiverse.http://www.thingiverse.com/thing:384680

This is a motorized solder paste dispenser for soldering SMT boards that was inspired by ithese things http://www.thingiverse.com/thing:384680 http://www.thingiverse.com/thing:1119914. ...Added ring for easy access to the buttons.

This is a manual solder paste dispenser based on a nice simple design by ylectron. I modified the design of the body so that one side is flat to make printing without support possible. I also modified it to fit 5-cc syringes rather than the larger...

Its a try to create a solder paste dispenser using cheap components from aliexpress. I've got my inspiration from https://www.thingiverse.com/thing:384680 and design it from a scratch. The biggest improvement is the plunger system. You'll need: ...

This is a motorized solder paste dispenser for soldering SMT boards that was inspired by this thing http://www.thingiverse.com/thing:384680. The home directory of this project is on github here https://github.com/zapta/misc/tree/master/paste_injector...

This is a motorized solder paste dispenser for soldering SMT boards that was inspired by this thing http://www.thingiverse.com/thing:384680. The home directory of this project is on github here https://github.com/zapta/misc/tree/master/paste_injector...

This is a motorized solder paste dispenser for soldering SMT boards that was inspired by this thing http://www.thingiverse.com/thing:384680. The home directory of this project is on github here https://github.com/zapta/misc/tree/master/paste_injector...

Solder paste dispenser remixed to add .2mm clearances between parts. ...Blender file includes the original models, the modified threaded rod, and the primitives used for modification (so other clearances may be quickly created.

If you use the smaller 30 mL syringes for solder paste or flux, this one might be a better choice. However, with both now, I'm covered for just about anything but a turkey baster. Nothing special to print. I used an 0.2 mm draft mode. No special...

This is a clamp to hold the paste syringe to the case. ...Original:http://www.thingiverse.com/thing:384680 Made:http://www.thingiverse.com/make:89888

Solder paste syringe dispenser, based on a design I found on the internet https://www.youmagine.com/designs/manual-solder-paste-dispenser I altered the design so that it is easier to print and assemble. YOU NEED: 1 x M5 nut 1 x M5 threaded...

<h2>RU</h2> После использования этого замечательного устройства, у меня переломались все корпуса от него. В месте, которое обведено на фотографии красным, оригинальная модель имеет, на мой взгляд, очень тонкую перемычку. Поскольку винты и гайки у...