solid edge 3d models

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

I am running the custom IR sensor currently, but I ran the custom firmware for several months previously.If you choose to use the custom firmware , you will need to remove the 90 degree header from the stock IR sensor and either replace it with a...

 Everything else can be 0.6Part counts:24 of the long bolts4 of the short bolts28 of the round nutsMake sure the threaded side is facing up3 pins One side of the slot in the end has an 0.2mm solid face.  This helps with the stability of the print.  I...

For that speaker, I ended up soldering solid 22 gauge hookup wires.Solder the rotary encoder to the center of the boardSolder wires to ground and 3.3V.Solder red (+) and black (-) speaker wires to left and righ speaker pinsAttach the 5V FTDI header...

So I tried to keep everything aligned by bringing the guides to an assembly on the upper and lower side, so as not to burden, and having a half-band attachment, the support is more solid and the movement on the X axis is less tiring precisely because...

Model made as 1/8 scale in FDM version and 1/16 in SLS/SLA version.FDM version dimensions: After being printed will stand:340 mm tall, 163 mm wide, 210 mm deep - with platform;237 mm tall, 115 mm wide, 98 mm deep - without platform; - Connectors...

This saves material and makes it easier to get pieces out. Added shaped holes in the bottom of vertical stacks. v1.12 Better support for compact fits. Bug fixes and optimizations. v1.11 Now supports rotation of features. v1.10 Under-box storage...

Fourth reason is that the shelf's itself get even more stable and feel more solid. Fifth reason is that the clock will be mounted in "mid air", so dusting is a problem. All the spacers and blocks fill up the gabs, so there is no way spiders and...

You can see that the perimeter wall ends just like in the example above, but a single (= non-looped) extrusion with decreasing diameter is printed down to the 0.1 mm area.Intersecting BlocksThis is a simple test that shows if a slicer can handle...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

The wires were visible from below and since my clock is mounted above a staircase, everyone looking up while on the stairs, would see the multi color wires between segments. The second reason was that light from the shelf lights escaped through the...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

for PLA+ (.3mf and .gcode are in 0.15mm with the .3mf being optimized for Prusa MK3s+ Printers that are well calibrated or factory calibrated)  Hot-End Temp: 220-225 for first layer smush and good adhesion if not using brim (not suggested since...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

That change has corrected the sag and it now feels very solid once assembled. The downside is that it is very hard to remove the sides now.<strong>That should not be a problem as long as the door and the M4 locknuts are assembled in the center module...

Besides that they are slightly longer for a better and more solid fit in the final assembly. 3 - New motor support The lift now uses a new type of motor which sounds and runs better than the original motor used in version 3. However I've added an...

Removable cloak and skirt which you can print with flexible materials;- All parts are divided in such a way that you will print them with the smallest amount of supports.SLS/SLA version features: - Made as a solid one-piece figurine;- Contains...

Cura uses an infill pattern with a 20% setting, but switches to solid bars, which are stronger, at 30%. These are the only fragile part of the design, especially if pushed from inside the body. Take care when fitting the LED matrix into place.No raft...

The solid state design of the LED lamps give this fixture superior resistance to damage from vibration, extremes in temperature and a lamp service life over twice that of standard fluorescent bulbs. This second generation lamp is offered in 5600K...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

Now lens and adapter looks like it is a solid lens chasis (if you will print it with matte plasic) ## List of changes: - added stronger ring around P6 bayonet - ring made with the same design as a control elements of a lens itself - EF bayonet...

So I tried to keep everything aligned by bringing the guides to an assembly on the upper and lower side, so as not to burden, and having a half-band attachment, the support is more solid and the movement on the X axis is less tiring precisely because...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

The following formula aren't exact but they should place the text in a good location close enough to where they should be:Xᵗᵉˣᵗ = -84 - (TextXsize/2)Yᵗᵉˣᵗ = -7.07 - (27.67-TextYsize)/2.66If your print won't be dual-extrusion, you can use the combined...

This is a fully solid-state version for 3d-print, this is not a scan version. At the photos you can see the contours of the models on screens with stl or obj files, it is enough to understand the possibility of printing a model or producing a...

Repeat step 12 to verify that the connections are solid.Move the USB cable so that ~ 2-4cm of the cable with all its protective layers are inside the bottom part. Use hot glue on this area of the cable to fix the cable to the bottom. Be sure that no...

Me puedes invitar a un café haciendo una donación Click to danateCATEGORYPART DESCRIPTIONQTYCOMMENTSFastenersScrew DIN912 M2x8&nbsp;4&nbsp;&nbsp;Screw ISO 7380 M3x66&nbsp;&nbsp;Screw ISO 7380 M3x25&nbsp;4&nbsp;&nbsp;Screw DIN912...