solidworks insert picture into part 3d models

MMP-2 is the part number for this magnetic mounting plate. ...With this plate in place, you can remove a light like the GL-3067-M when not in use, but it will stay firmly affixed during use.This clamping system is effective on heavy equipment, boats,...

Here is what I came up with: This model consists of 3 printed parts. Then you need something with ø3 mm diameter as an axle. Anything like a wire or nail would do. Just cut it to a length of 18 mm. Fix the lever in the holder with this and make...

Explosion proof, impact and heat resistant Pyrex tubes provide lamp protection.Lamp OptionsLamp options for UV fixtures are determined by UV range.Operators can specify when ordering- UVA (-A part number suffix), UVB (-B) and UVC (-C suffix).F17-T8...

Cost less than 30€ (3D printed parts excluded) from china. Similar commercial device in store 400€!!!! "Radin" in french mean greedy ;). Calibration at startup with 50g weight. To set the weight 2 buttons + & - . One memory button (5 stored target...

I program mine to turn off the heat bed when it gets to part 3, but this sample gcode and factory file the heat bed stays ON (for those glass bed users). I can't afford the E for that many machines running 24/7. Already pushing $100 a month in E...

The only part that needs support is the bracket arm, which should be printed with the long narrow edge on the bed, 'teeth' of the joint facing up. Post-Printing I lightly sanded the diffusors with 120-grit sandpaper to make the light even more...

https://www.youtube.com/watch?v=5Y1Psf6igHE Step by Step instructions: https://www.instructables.com/id/Juuke-a-RFID-Music-Player-for-Elderly-and-Kids GitHub: https://github.com/ananords/Juuke ••• Parts: ••• Arduino UNO...

The design of the knob making it difficult to print it without using supports, I chose to make it in two parts which will be glued back to back to obtain the complete knob. To facilitate gluing and make the piece more solid, there are also 6 small...

The latter can be easily soldered onto the AD9833 board and is thus quite easy to install. Other parts used: 1.8" TFT LCD (SPI)...

If you want to recreate this you'll need the following things: -transparent filament for Playstation logo -black (or colour you want) filament for the lamp case -on/off snap in switch...

The Rebellious Slave was part of Michelangelo's artwork perfectly put together to impress viewers and convey his message. The use of cool and warm colors makes the sculpture look impressive while maintaining its intended theme. ...Michelangelo was also...

Anyway, try printing these models on your printer in ABS (or PLA if that's all you have) and post a photo here showing how much you can avoid warping, and print a finished part with a perfectly flat bottom. Good luck! -- Jim Newton Founder, TechShop...

Parts Printer using a Makerbot Replicator 2X at Bradford College - UK and the front wheels made from Aluminium or could be printed from the students' own design. The rear axle was turned from Nylon and we stepped this so that it increased the speed...

You can use this collection as part of the MEDIEVAL_ANIMATIONS_MEGA_PACK. Humanoid avatars must be used when redirecting animations to custom characters, but horse animations can be utilized with any rig type except for humanoid. Note that there is...

This shows the selected part of the object. Therefore, you can move this little triangles at the bottom and top of the timeline. You move the top triangle until you only see one layer above the holes. Now you click on the small <strong>+...

Parts Needed : 1x M5 hex nut and 1x M5 bolt (20mm minimum, the longer the bolt, the more pieces you can stack up. The jig is basically constructed using multiple copies of a single 1/8" high (3.175mm) piece about 3.5" long and 5/8" wide. It was...

The most complicated part of this has been to build a black and white image of the relief of SPAIN, I share it with everyone because it has been very difficult to get it, in fact, I have made it by gathering data from a lot of sites. To make...

The "business end" of the rocket should use a combination of this AND a high quality 2 part structural epoxy (Oddly the epoxy won't, bond the plastic, but it will add structural support). I cannot and do not recommend CA's (cyanoacrylates) it is not...

It is a traditional method of tobacco use throughout South Asia and parts of the Middle East, where beedies are popular and inexpensive. In India, beedi consumption outpaces conventional cigarettes accounting for 48% of all Indian tobacco consumption...

It then shows you how to make a cell phone app to display the data.The project parts:Dylos Air Quality Monitor ( https://amzn.to/2V8Uy0W )RS232 to TTL Converter ( https://amzn.to/376AdyM )5V Micro USB Power Adapter ( https://amzn.to/3pZ3MLn )Particle...

&nbsp;When assembling, put the lens in the base, screw the middle part with the hexagonal grid on, and then put desiccant in the top and screw it on. &nbsp;I made the middle and the top the same dimensions so I could leave out the desiccant as...

** You can purchase this case printed from my store by clicking HERE **This is a case for the TTGO T-Beam NEO-M8N and NEO-6M boards, designed for the Meshtastic project (https://meshtastic.org).There are only FOUR files required for a complete case,...

For this parts is used the following components: "->" [3D-printer "Sidewinder...

I also added two more teeth to click from the side.It can also be used with the 3M 603 FILTER ADAPTER which I also drew and can be found here: https://www.thingiverse.com/thing:4215903I added a new product, a series of half mask filters...

FINWIDTH and PLATE are the thickness of the parts, if they're too flimsy you could make them fatter. FUDGE modifies the "optimal" values to account for print variation, etc. You can increase this if your tubes are too tight. In the clips files the...

For infill, if you use less, you'll have a lighter part, but it will be weaker! I'd recommend 70%. I think that's what I used. ...Maybe.</p> <h3> How I Designed This</h3> <p><strong>AutoCAD</strong></p> <p>All I really did was use some calipers to get...

As part of this enriching journey, I embarked on a project that would culminate in the creation of an extraordinary prop. This cutting-edge brain-inspired prop is the culmination of months of meticulous research, collaboration with top experts, and...

For post-printing hardware, you'll need to either pick up a lamp kit or separate parts from Home Depot's lighting department shelves. For my first build of this lamp, I used the following items: * Westinghouse Porcelain Keyless Socket Adapter Kit...

Used to compute the width of lip in lightbox lithophane_thickness = 7; //Thickness of widest part of lithophane if using a border it will be the border thickness box_lip_angle = 60; //When 3d printing angles of at least 50 degrees are necessary to...

This object is part of "Scan The World". Scan the World is a non-profit initiative introduced by MyMiniFactory, through which we are creating a digital archive of fully 3D printable sculptures, artworks and landmarks from across the globe for the...