sonic r model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

For all options please visit the listing on pintables here: https://www.printables.com/model/253827-ultimate-card-box Thingiverse will not let me upload zip files anymore nor make folders and this box has over 120 unique versions/files. Assembly: ...

The spacer is to put between the 5015 fans and the cover, if your spacing is larger/smaller just scale the spacer on the Z axis to match your setup. The hole for the mounting screw is designed to be 4mm in diameter, but if yours end up being...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_position = 0 custom_right_port_y_position = 0 custom_phone_thickness = 10 stencil_pattern_element_rotation = 0...

OK, this isn't a model but rather a gcode script to facilitate automated cold pulls to clear out your nozzle. I use it all the time on my Ender 3 and thought others might get some good use from it as well. **What is a cold pull?** A cold pull is...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

 It's printed in vase mode with 0.2 mm layer height using 0.6 mm nozzle to avoid clogging and to increase the strength and impermeability to light.PETG parts are designed to be printed without supports - in some of the models there are tabs to brake...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_length = 40 custom_top_port_length = 70 custom_top_port_corner_resolution = 8 stencil_size = 40 printer_tolerance = 0.4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_port_x_position = 20 custom_back_camera_corner_resolution = 8 custom_bottom_fillet_resolution = 8 stencil_horizontal_position = 50...

Janson comments, is that "they knew how to die, barbarians that they were." The Dying Galatian became one of the most celebrated works to have survived from antiquity and was engraved and endlessly copied by artists, for whom it was a classic model...

(I have included a model with logo, and one without)Assembly Instructions:Print the box and two clipsInsert bowtie shaped post on clip in to corresponding hole on box, then rotate until the push-clip lines up with the hole.Push the push-clip in to...

Rollerspooler is the latest in TUSH-Varientalology, using the base Idea from the original The Ultimate Spool Holder (by filamentry) then adding the Clamp from the original Prusa Spool Holder (because, why reinvent a perfectly working wheel?) to mount...

Stereographic Projection based on the excellent work shared here: https://jasmcole.com/2014/11/01/stereographic-lampshades/#more-650 I used Blender's "Solidify" modifier to add various thicknesses to this model for printing. I recommend printing one...

This station involves three separate 3D printing processes:Main housing (220mm x 220mm)Rotating disc (172mm in diameter)Gears, gear holder, and "engine" stick componentsMotivationThe primary motivation behind this design was to facilitate the...

I thought about being edgy and calling this v6.66 but I figured a name change would provide a clean slate for the community to build from.Starting with my printed Gecko 1.0, I painstakingly modeled the entire blaster in Fusion360. There were three...

- An increase of thickness from 0.5mm to 0.6mm, which should allow a wider variety of resolutions and nozzle sizes to print the design and make the end-products more reliable between printer models. Thank you again for your support and enthusiasm...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

You can subscribe to my youtube channel if you would like to receive a notification when it comes out.There are so much detail on the model to help hide the layer lines that I do not find it necessary to do any sanding. I did spray the frame first...

This model is for a “streetlight-style” wired garden/pathway light. Brighten up your garden path with lights, without spending a fortune on MoonRays or similar products where a single lamp can cost up to $20! In bulk I can make these for about $3-5 a...

... - The +1mm fan duct is for use with longer non-standard m6 nozzles - Use the following commands to use with stock Prusa firmware: M92 E690, M500 - You may need to adjust the extruder motor current using M907 but that depends on your motor model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

For other sizes of tube or different grid arrangements, you can use the Thingiverse Customizer to remix your own version (the recommended way, so others can benefit from your work) or download the model and use the OpenSCAD Customizer (available in...

Therefore, I invite you to play with the assembled model in the 3D viewer above to get a better feeling of its shape from all sides. Here is a video of the structure before planting moss on it:</p><figure class="media"><oembed...

&nbsp;I've included 3mf project files from PrusaSlicer so you can see how I ran this model on my printers.&nbsp;UPDATE 27/01/2022: Created a rudimentary mount to hang the chassis under a shelf or table. &nbsp;I decided to make a second unit to move...

You can fit dividers in any space, and they fit next to each other too if necessary, but you probably don't want to fit one in the front space as it will block the finger hole in the front of the drawer.If you make one of these, please post your...

OpenSCAD is a script-based modeling software specifically created for projects like this that need to be customizable.If you're new to the program, it may look strange at first, but most of the work is just typing values into a form or selecting...

don't use tin based silicone since it's not high temperature resistant) For this model you need not more than 30ml of silicone in total (15ml A + 15ml B), but if you buy 500ml or 1000ml tare, you'll have a lot of fun creating molds and casting cool...