sparkfun pro micro 3d models

Small bumper case for the Sparkfun Pro micro board. ...19/06/2016 Update: added new version to correct the USB cable plugging end.

This is a quick hand measured model (no guarantee of perfect accuracy on dimensions, but should be close) of the pro micro arduino available from sparkfun.

Case for Sparkfun/Arduino Pro Micro Threading is M2x0.4 5mm Glue the Arduino in place or use some shrink tubing to press it down with the lid.

SparkFun micro:bot kit for micro:bit - v2.0I wish SparkFun provided a 3D model, so I made one. The model is based off caliper measurements, so expect some error. Overall, I think it's a pretty accurate model. I sourced some parts from other CADers.

The SparkFun RP2040 Pro Micro board has a pair of small buttons that can be used to place the board into reset mode. After installing headers on the board, it can be difficult to access these buttons. This tool fits the buttons without hitting any of...

Arduino Pro Mini by Sparkfun

A "coaster" for a Sparkfun Arduino Pro to keep the board off your table. Not tested with a shield, but should work. ... Created based on the board image from the Eagle files provided by Sparkfun.

‎La SparkFun Pro RF es una placa inalámbrica habilitada para LoRa® que combina un SAMD21 y un RFM95W de largo alcance para crear una placa IoT Arduino compacta y fácil de usar. ...Con su rápido MCU y excelente transmisión de datos punto a punto en la...

Simple Model of:https://www.sparkfun.com/products/11113

Spark Fun Board Mega Pro p/n DEV-11007 converted from eagle pcb.

This is a clone of the model done by user "paco" (Sparkfun Mega Pro ). In this version I added a solid of the SMD JST power connector. ...Will use this 3D printed model to test fit enclosure and other PCB designs.

This is a very simple case for the [SparkFun Pro RF - LoRa](https://www.sparkfun.com/products/14916). There are two lids: * One is a two piece lid with a ventilated cap, which is intended to hold a [QWIIC Sensor](https://www.sparkfun.com/qwiic) -...

Just a simple mount for the Sparkfun round rocker switch. It either slides or snaps in the top of the rear 4040 rail and sits flush to the back of the PSU. The rear lid can be either secured with 2 M3x5mm screws OR just by friction. Print the...

The lid has holes for a [SparkFun Micro OLED Breakout](https://www.sparkfun.com/products/14532), a reset button, a buzzer, and a grill for the microphone. Read the full build instructions on Hackster:...

Holder for the Sparkfun Gamer:Bit controller that connects to the BBC Micro:bit and standard double AA battery pack. I used some hook and loop for the bottom of the battery pack and just some double sided tape for the board, it holds in well and puts...

... sumo shield for the the RedBot. ...I couldn't quite use it because of the the line follow sensors that are part of the Micro:Bot kit. I moved the two lower pins in a bit to account for this. ...The rear shield worked perfectly without modifications.

The Sparkfun Pro Micro ATmega32U4 5V 16MHz will work also. There are extra board installation steps for the Sparkfun board that are on their site. I included the sketch that I used for my project and the .stl models for the case of course. ...

... ... * [Uses this USB cable to go from case to component.](https://www.adafruit.com/product/3258). * The screws are not my design, but downloaded from McMaster-Carr. * Posts are for mounting (QWIIC sensors)[https://www.sparkfun.com/qwiic]! ...

ARDUINO PRO MICRO Model

Foxeer Arrow Micro Pro

Pro micro case

Basic enclosure for Arduino Pro Micro https://grabcad.com/library/arduino-pro-micro-1

Case for Arduino pro micro and one button

Remixed the Arduino Nano Holder to work on the Arduino Pro Micro.

Made this case for a project, the pro micro snaps into it just needs some force  

A case for the Arduino Pro Micro. ...Just hot glue the sides together.

3D print and use this model as a arduino pro micro board casing.

Arduino Pro-Micro (yes I did another one) I think this may have been pioneered by Sparkfun but open to correction there. Basically its an Arduino Leonardo shrunk until it fits in a 24 pin DIL socket. This is the important bit none of the Genduino...

Chassi for Arduino Pro micro. ... When I made this chassi i use a 3d-model of Arduino Pro micro. ...But my board was bigger than 3d-model. You might need to grind a bit on the sides.

Here is a Arduino Pro Micro,with and without header, for test and design purposes. ... Have fun with it