speaker mic 3d models
19136 3d models found related to speaker mic.thingiverse
I wanted a little stand that a speaker mic can clip onto so that the speaker is facing me instead of lying on my desk. ...The base of the stand probably could use a redesign so that a weight can be integrated into it, but it gets the job done.
thingiverse
Of course, there are more high-quality Speaker Mics on the market, but the result is notable after the modifications. The RJ45 plug and the inner life of the jack plug are fixed with a few drops of super glue from the inside of the Plug. The final...
thingiverse
... plug for the [(tr)uSDX](https://dl2man.de/). ...The plug can be used with cheap Baofeng speaker/mics that are readily availble on ebay, aliexpress, etc. ... See [here](https://hb9hem.com/modify-baofeng-speaker-for-tr-usdx/) for more details.
thingiverse
I lost the speaker / mic cap from my TyT MD380 DMR handheld and needed a new one. This is my first attempt to create a replacement. It fits nice, doesn't drop off operating the handheld radio, so for now it's good. ... There is a 2 part version...
thingiverse
After messing about with several fixes including using rubber bands and glue to support the jack in the correct place I finally designed a proper bracket to support the speaker-mic cable. It holds the cable in such a way as to prevent lateral forces...
thingiverse
Replacement speaker cover mesh for CAT S60. I printed it with PLA850, on 0.1mm, 100% infill, 0.7mm height. ...Glue it in with uhu universal (just a drop in each corner and middle).
thingiverse
Baofeng UV5R Speaker Mic Retention Clip with more rounded edges as requested by turbo2ltr. ... Tweaked it in SketchUp, and post-processed through NetFabb's Cloud "Model Repair" to make sure nothing was wonky.
thingiverse
I removed even more material, and thinned out the back strap that attaches in between the radio and the clip The thickness was pushing the clip too far from the body of the radio, and was unneccessary for use.
thingiverse
This is version 2 of my Icom IC-2AT speaker microphone port cover. Version 2 is made from TPU and goes around the BNC antenna connector. ... The original was made using PLA and can be found here: https://www.thingiverse.com/thing:3736393
thingiverse
The Xiegu G106 is a great little radio, but it doesn't have an audio out jack, this little project will fix that. You will need a RJ9 panel mount jack, a 3.5mm panel mount jack and a RJ9 male connector. This is a quick easy print, less than 1 hour. ... ...
thingiverse
Print Solid, at a high resolution, for the holes to be accurate. Recommend 0.08 mm layer height, 2 wall. You will need the original spring or a small piece of metal bent to fit in there as a spring. There is now a version 2. In the second version,...
thingiverse
I have the same problem as most with the UV-5R. If you move the headset plug slightly, the radio will no longer work. There is already a solution for this here. However, I didn't like it because it is too bulky and you have to buy screws. The...
prusaprinters
<p>I have the same problem as most with the UV-5R. If you move the headset plug slightly, the radio will no longer work.<br/> There is already a solution for this here. ...However, I didn't like it because it is too bulky and you have to buy...
thingiverse
;-]) This has a reverb box below the speaker and one below the mic both with holes to open to the front; honestly I haven't tested enough yet to decide if these are adequate or need more work, but it's a definite start and I thought I'd publish it so...
thingiverse
... is a cover for the MIC/SPEAKER connector, if the original cover is missing, this thing can help you. ...Designed for the Wouxun KG-UVD1P portabel radio, but possible fit other radio's with similar speaker/mic connector. ...(Kenwood / Baofeng..etc..)
prusaprinters
This platform and adapter allows you to place a bookshelf speaker on a standard desktop microphone stand.This platform was designed to fit the Monoprice MM-3 desktop speakers. The platform is 146.5mm x 111.5mm.</p><p>The project comes with two prints...
thingiverse
... so I can keep 1 ear open. ... Well, it snapped off and I printed the snap brace I found. Problem is, it has a mic that doesn't really fit and a power button that's covered up. Did some quick edits and made this. ... It's meant for your right ear.
thingiverse
Designed with FUSION 360, sliced with CURA 4.6.1, 3hours 41mins print time. ... It was designed specifically for my Iphone 11 with microphone inlet on the left of the phone base, speaker output on the right of the phone base. ...
thingiverse
Case for Rhasspy Pi Zero wit Respeaker 2 Mic Array and a small Speaker. Fits in the hole from other DOTs. If you feel like sending a tip please use this link: paypal.me/AndreasFohl and, to those who do, thanks in advance! ...
thingiverse
This is a case I designed for a Raspberry Pi 3a+, a connected Seeedstudio 2 mic pi hat and an Adafruit 3W mono enclosed speaker. ... It features: + a wall mounting hole in the bottom + snap on lid + integrated button for 2 mic hat button + funneled mic...
thingiverse
#This Case is for the Rpi3A+ **Things you will need:** [Raspberry Pi 3A+](https://www.raspberrypi.org/products/raspberry-pi-3-model-a-plus) [Respeaker 2 Mics Pi Hat](http://wiki.seeedstudio.com/ReSpeaker_2_Mics_Pi_HAT) [Adafruit Mono Enclosed 3W...
thingiverse
This is a case for Snips voice assistant Serveur. https://youtu.be/ntZ5uNX4TGM UPDATE i modify the screw hole because M2.5 screw doesn't fit. If You have the V1 model, you hav to put M3 screw. i made top case more larger. ...But the V1...
cults3d
This is a case for Snips voice assistant Serveur. https://youtu.be/ntZ5uNX4TGM UPDATE i modify the screw hole because M2.5 screw doesn't fit. If You have the V1 model, you hav to put M3 screw. i made top case more larger. ...But the V1 model is ok,...
thingiverse
A TABLE BASE FOR MICROPHONES, (FITS MINE FOR VONYX BLUETOOTH SPEAKER MIC). 10% INFILL FOR PARTS. (SUPPORT (EVERYWHERE IN CURA) REQUIRED FOR PRINTING THE BASE INTERIOR). PARTS ADAPTED FROM OTHER THINGIVERSE USERS INCOMPLETE/ MISSING PARTS /INCORRECT...
thingiverse
Desk stand includes charging and amplification for speaker and mic.
thingiverse
A stand for a Kenwood TH-D72 HT to allow it to sit on a table and use a speaker mic. ... Also has a mount for a KES-3 speaker.