spektrum dx9 3d models
742 3d models found related to spektrum dx9.thingiverse
Hallo, hier ein einfacher Knüppelschutz für die Spektrum DX9 um den Sender in einer Tasche zu verstauen. ... Grüße, Bernhard http://youtube.com/channel/UCuGMUCh7iKq4J6Uhd_ZcNQg
thingiverse
This is an alternative version of the DX9 antenna adapter cap for higher gain (dBi) antenna modification of the Spektrum DX9 radio. Option 1 – One Antenna For use with one SMA-connector, and one «blind» SMA-connector for storing one dummy load...
thingiverse
Since there are not many gimbal stick protectors available for the Spektrum DX9 I decided to make my own. Might fit other Spektrum radios but I do not own any other so I can't verify myself. How you can check: * stick diameter: 8mm, protector...
thingiverse
A full sized TBS crossfire bracket that clips onto the handle of the Spektrum DX9.
thingiverse
Replicate of Spektrum DX9 - RC Radio Transmitter Best print it in 45 angle with support. ... Did 3D scan it with Meshroom and did get help with finish it.
thingiverse
Gimbal Saver for the Spektrum radios. Fits DX9 and DX8. I suspect it also fits the other DX series. 11-26-2017: Update Version 6 the hole between the saver and lanyard clasp line up better. I print all my gimbal savers out of TPU now.
thingiverse
This wall mount is a little bit more narrow than my other one I made as the DX9 Transmitter handle is slightly narrower. ...I printed it standing straight up at .3 and it printed great.
thingiverse
It can be used with: Antenna cover with pigtail location for Spektrum DX9 (single antenna) http://www.thingiverse.com/thing:1592674 Antenna cover with 2 pigtail locations for Spektrum DX9 (twin antenna) http://www.thingiverse.com/thing:1592720 2.4...
thingiverse
Set of x2 Throttle limiting wedges for a Spektrum DX9 these parts are not available from Horizon Hobby. I've printed and tested and the fit great, job keeping them from warping. I found with PLA a 65 degree bed did the trick. I have these installed...
thingiverse
Have been using the **IISI Cockpit V2** telemetry for RC plane flying for a while now with my **Spektrum DX9** transmitter. While I was very happy with the hardware itself, so far, I've always had to attach the Cockpit to my Tx using velcro - not...
thingiverse
... at my local dollar store and cut it out on my laser cutter. It was a lot less expensive than the $14 option on Amazon. Note: The photo shows a coupon sheet I cutout on my laser cutter to demonstrate that the profile does fit the screen of the Dx9.
thingiverse
Just a remix of this item to include a stand. ... When using my DragonLink mounted on the back, my DX9 tends to fall over. Also, I've included a port (you can use the female end to be flush) to power the DragonLink. Nothing fancy. ... Just functional.
thingiverse
To connect gimbal protectors from "sebsx" for Spektrum Radio DX9
thingiverse
Great DX9 Mount for the TBS Crossfire. Fits perfectly. ...
thingiverse
Remix of DX8 Gimbal Stick Saver from DavidCanfield Now fits the DX9 Gen2 Black Edition. ...WIll probbaly fit other DX9 G2 transmitters but I've not tried.
thingiverse
I made this plug for my DX9 so I could clean up the look of the accessory port that I used for passing the wires through to my TBS Crossfire. ... Print with flexible material like TPU
thingiverse
Assembly instructions: http://www.canardwifi.com/2016/05/27/augmenter-la-portee-dune-radiocommande-2-4-ghz-exemple-dune-spektrum-dx9/ (in french, use Google translate if needed) Pigtail:...
thingiverse
You can put 1 or 2 boosters on it, and it can be used with: Antenna cover with pigtail location for Spektrum DX9 (single antenna) http://www.thingiverse.com/thing:1592674 Antenna cover with 2 pigtail locations for Spektrum DX9 (twin antenna)...
thingiverse
Simple mount for Immersion RC's EzUHF Long Range Transmitter for SPEkTRUM DX9. The goals were: 1) Get the EZUHF antenna in a different orientation than the DX9 2.4 GHz antennas. 2) Minimize any interference from the EzUHF 70cm into the DX9. 3)...
thingiverse
My first design antenna cap broke after a few years, so I designed an updated version. ...
cults3d
My first design antenna cap broke after a few years, so I designed an updated version.
thingiverse
I made this battery cover / battery holder for my DX9 to hold a Tattu 3S 850mah 45C battery for use with my TBS Crossfire.
thingiverse
The DX9 transmitter has an uncommon rear mounting bar which doesn't currently fit many of the existing adapters for the long range transmitter modules. ...Using just some 3/4" aluminum bars, velcro and sticky foam, you can create an adapter that keeps...
thingiverse
Now it can be slic3d. ... Also cleared connection flaws (circles and bridge).
thingiverse
Remixed to make the "shoulders" a bit less wide, from 104mm down to 94mm.
thingiverse
Probably work with transmitter in same generation ( DX7 and DX8)
thingiverse
Assembly instructions: http://www.canardwifi.com/2016/05/27/augmenter-la-portee-dune-radiocommande-2-4-ghz-exemple-dune-spektrum-dx9/ (in french, use Google translate if needed) Pigtail:...