spinning display table 3d models

Although inspired by the Atreus, I couldn't quite find the right compromise among the non-split ergo keyboards, so I decided to make my own.Features:1x RP2040 (KMK on Raspberry Pi Pico), USB-C port50x switches1x SSD1306 128x64px 0.96in IIC OLED...

With settings X=40, Y=40, Z=50, C_scale=0, C_offset=5, it will make a 40mm calibration cube, with a 5mm radius on each corner, like: ![40mm cube with 5mm radiused...

if you do test it, please post pictures and leave a comment.V3 mount has been tested and working on the SKR PRO V1.1==================Ribbon Cable Breakout PCB BoardBeefed up trace width where possible.Heater PCB trace has trace on both Front and...

This a full-size replica prop with rotating stirrups and pedals for display and cosplay purposes. It is not an exact replica, but has been modelled from many internet images and video references. When printed as per instructions...

I used a light peg to display the blue connection indicator on the front panel. Annoying that it flashes constantly while operating. This particular board needs 12 - 24 V, and running from 12V with 4 ohm speakers gives the best performance - from a...

The temps of the exhausted air range between 94F to 100F while gaming (as displayed on the fan controller). The GPU ranges from 65 to 74C while gaming and the CPU ranges from 60 to 70C. My build is a 5600X CPU and 3060ti GPU. I printed the vent...

  The figure trays: there are serval figure trays all these have a hole in the bottom that fits a 10x1 mm magnet if you want the figures to be more secured, however this is NOT a requirement, and the are standing fine without.It is important that...

The Customizer tool that made this possible can be found at http://www.thingiverse.com/apps/customizer/run?thing_id=58001 [60 words] --- A personalized edition of the design located at http://www.thingiverse.com/thing:58001 was created using the...

treaties, on display. Retrieved March 10, 2017, from http://www.navajotimes.com/news/2014/091814treaties.php Treaty of Fort Jackson. (2017, February 26). Retrieved March 10, 2017, from...

I had to resist simply copying Emmett's design, so I added Cupid's Arrow and a display stand to give it a personal touch. The arrow is available in both dual-extrusion (because I can do that) and one-color versions. However, the two tips and tails...

A self closing cabinet hinge is used to keep the plate rigid in either its displayed or tucked form.Printing NotesPrint Fender Elim V4 in an orientation best suited to your printer's build volume. PLA is perfectly suitable for this part. I am able to...

Sophie Turner, famous for her role as Sansa Stark in Game of Thrones, proudly displays a pear-cut diamond engagement ring from husband Joe Jonas during their off-screen time together. Z oe Saldana's stunning emerald, set into a gorgeous pear...

The OpenSCAD generator displays the outside box dimensions for reference so it would be relatively easy to tune all the dimensions to fit together perfectly before printing anything. I included the .stl files I used in the pictures of the assembly I...

The primary file boasts an enormous resolution of 4096x4096 pixels, displaying incredible texture detail with multiple images: Albedo (main color) Specular (shine and reflections) Glossiness (degree of shine and polish) Ambient Occlusion (shading...

The ESP8266 can connect to a data source and display status on the LEDs. I use it to read out the status of my garage door and other sensors in my home. The ESP8266 connects to an MQTT message broker and receives messages to control the LEDs.I...

CTR_leg_f.L, CTR_leg_f.R, CTR_leg_b.L and CTR_leg_b.R are IK controllers of the limbs, an with customized attributes: IK-FK controls the IK/FK non-seamless switch of the limbs; Pole_target switches the different display mode of pole vectors of the...

... than during non-rutting periods. These changes are characterized by decreased feeding, increased time observing their surroundings, and increased behaviour changes. Ewes are also predicted to be slightly receptive to the displays of the rams.

Hardware used: FC - Naze32 rev6 (direct soldered wiring, no pins) ESC - DYS 4in1 20A MOTORS - Racerstar 2205 2300kv PROPS - KingKong 5045 Tri's (with 5mm tip trimming) RX - FRSky R6b (decased and unused pins removed) BATTERY - ZOP Power 11.1V 850mah...

If you find there is excessive space between the display and the case, try adding some spongey foam or tape to get a tighter fit. If when printed these protrusions are too large, file them down for a proper fit. Because the enclosure is so small and...

I designed this display stand for FPV style drones. Whilst I built this from scratch, there are a couple already on here that I took inspiration from, but I found them either unbalanced or that they require a crazy amount of support material to...

This tablet is pretty old and slow, and in the future I'm going to replace it, that is why I made it like a modular design so it can fit almost every tablet, smartphones and also hdmi display you can connect to the Raspberry Pi itself. I think this...

While the model can be printed for display, it is meant to be flown. I designed this model for NAR or TRA Level 1 HPR certification. The advantages to the builder are several: 1) It is easy to print, modify and build to suit your tastes and...

The user interface includes a commonly available I2C LCD Display Module 128 x 64 Pixel for Arduino. All is based on open source and commonly accessible parts; especially for the mechanics the objective is to be scaleable in production and hence...

Do not put it in an indoors window sill, even just for display! - Blindness! Focusing a 100mm diameter patch of sunlight into a 1-2mm diameter patch results in an incredibly bright point of light that WILL blind you at least temporarily in at least...

The rigged version is in the initial pose, previews are just for display. Textures can be compressed for faster running when the character is placed in the midground and background. The hair dynamics have been baked and are ready to be used. ...The...

Just glue to the Back.MaterialsYou'll need:PLA filament2 x 8x3mm Magnets (100 of these are <$12)[Optional] Super GluePrinted ComponentsAll the parts fit on a Prusa Mini (180x180mm) bed and are included in the file.They're separated and named, so...

Create a Lasting Display of Your Cherished Photographs or Print a Stunning Gift for Your Loved Ones. To create this unique lamp, you'll need a print bed with a minimum size of 150mm (6 inches). My design is inspired by other similar lamps on...

- Adapted the front to hold the 0.91 Oled display.  Features:Manual set the Laser power or use PWM control, check laser temp and off;Parallel in-out on DS 15 connectors (in from CNC controlboard, out to aux) this is an option, use it or leave...

Boy, was I wrong.By chance, it turned out that these first tests could be an extremely accurate display of how well the Live-Z was tuned. (If you play around with the modifier settings, you will see that the effect is much less visible with other...

To be powered from standard 5v USB wall wart for full time display. My preference was CLEAR LEDs which accented the silk filament MUCH better than diffused LEDs, which reduced the brightness and shine of the silk model. Started with Amazon...