sploof 3d models

A pocket-sized dryer sheet sploof with caps to seal in residual smell after use.

Just a simple plastic sploof body that you stuff with dryer sheets. Blow into the big hole. ...Print Settings Printer: Printrbot Simple 1405 ...

... printed its ready to use. I recommend using 3 dryer sheets for this. Two placed at the base of the sploof in the circular niche and one covering the base of the sploof with the help of a rubber band. ... Enjoy and share with your friends!!!

This is a compact sploof I designed in Autodesk Inventor. Make sure to print the top upside down, use a raft. You will need 3 dryer sheets, I used bounce brand "Outdoor Fresh" smelled. Rip the 3 dryer sheets in half and stuff 4 pieces down the 4...

#Carbo-Sploof ##Personal Activated Carbon Sploof/Smoke Filter ###About This simple two-part personal smoke filter is designed to be filled with activated charcoal pellets. The pellets absorb and reduce odors that are blown through it. You can of...

Got roommates or neighbors who won't like the smell of your smoke? ...No problem! Fill with dryer sheets, activated charcoal, etc to create a working sploof for indoor smoking!

Activated carbon sploof, put a circle of dust filter mask material in the cap with the ring on top. Then fill with activated carbon. ... You can buy activated carbon in most pet stores in the aquarium section.

... just search for "Braun coffee machine filters". The activated charcoal absorbs a vast majority of the smells. Simply place the activated carbon filter into the end of the sploof then cover with the cap. Exhale into the sploof then repeat. ...:)

... there are any problems with the scaling. I'd strongly suggest putting the mouthpiece on the other end of the sploof unlike the pictures so that if anything leaks out of the gap, it will have already been filtered by a majority of the dryer sheets.

### Sploof of can filter design. ### OuterTube.stl and InnerTube.stl are soley present should you wish to check your retractions before committing to a long print. Carbon goes between the two perforated tubes. You blow in through middle hole....

this i a small sploof you put activated charcoal in and youre done

I put activated carbon in the center chamber and fabric softener sheets in the outer chamber.

https://www.youtube.com/watch?v=8_TugY3g9Q8 pack it with whatever, use filter paper/cloth on either end with a little cotton buffer to catch fines

Ultimate Sploof Air Filter V2 Ready to print. The idea behind this design is to keep the carbon dry as much as possible by using a segmented air-filter, you can put paper on top part as some kind of pre-filter and carbon on mid part, so you can...

Sploof for indoor smoking! ...Fill with dryer sheets and activated charcoal to create your own sploof to filter the smell of your smoke! Simply blow into it. ...Equipped with twist-to-lock base so you can replace the contents whenever necessary.

If you are interested in printing this design, I would not use those files from that zip.ABOUTThis is my custom designed sploof that I am sure is not an original idea. That being said, I was not happy with the offerings on Thingiverse/Prusaprints,...

Customized version of https://www.thingiverse.com/thing:1848038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1848038

Customized version of https://www.thingiverse.com/thing:1848038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1848038

Just seal off one end of the filter and fill it with activated carbon. Seal off the other end and screw the filter into the cone. I used the fabric of some old clothes and a rubber band to keep the carbon in place. The threads can be a bit...

Customized version of https://www.thingiverse.com/thing:1848038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1848038

Ona Gel in outside center chamber and activated carbon in the outside chamber. ...Fabric softener sheets in the bottom chamber.

activated carbon in the chamber below the mouthpiece, ona gel in the next, and fabric softener sheets in the bottom chamber.

Print the center at a rapid setting but the top and bottom at a fine or medium setting for best results.  To secure the top firmly use a piece of electrical tape to prevent sticking.

***Requires a 3M 6895 gasket for the 3M 2097 or 2091 filter*** The **2097/2091 filter is absolutely required** because it is rated for the particle size, but only filling the tube with carbon and not using a filter should work as well, but isn't...

A great way to take away any scent from smoking. Just blow the smoke directly into the spoof. When 3D printing offline you must add drier sheets to take away the smoke. ...Or instead of 3D printing you can visit https://www.kushgodproducts.com to...

Customized version of https://www.thingiverse.com/thing:1848038 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1848038

... smoking has a new look. ...Fill with dryer sheets and activated charcoal to create your own sploof to filter the smell of your smoke! Simply blow into it. ...Equipped with internal twist-to-lock base so you can replace the contents whenever necessary.

The design by mikeballs is fantastic. However, I always struggled to unlock the bottom cap. I constantly turned it in the wrong direction. I added a small lock symbol and an arrow on the bottom to fix this problem. Advantage: Never turn the bottom...

Hello Fellow smokers! I had grown tired of purchasing Smoke Buddies to help maintain a fairly smell free environment. Unimpressed with the options I found for making or printing my own filter I decided to produce my own. This design is meant to be...

Stubby mouth piece for 3m sploof, use ***3M 6895 gasket and 3M 2097 or 2091 filter***