stand for macbook pro 3d models

Folding stand for MacBook Pro, glued with double-sided tape

A two piece stand designed for MacBook Pro 13". The inclination of the base is a reasonable 20 degrees, which also allows for a additional adjustment of the laptop's lid. The stand's slot is elevated from the table by 2 cm at the lowest point. The...

vertical stand for Macbook pro 13" 2018

"The geometric stand" for MacBook Pro Retina will raise your laptop and your back will say thank you! . . ... Info: "The geometric stand" is designed for Macbook Pro Retina 15 ".

Laptop stand with folding feet. ... It's a stand for MacBook Pro 13-inch, sized for the 2018 generation but will work for any object of the same size.

"The geometric stand" for MacBook Pro Retina will raise your laptop and your back will say thank you!What is it:It's a stand that allows you to raise the height of your screen. Is thought to use the opening angle of 120° from your MacBook Pro...

"The geometric stand" for MacBook Pro Retina will raise your laptop and your back will say thank you! What is it: It's a stand that allows you to raise the height of your screen. Is thought to use the opening angle of 120° from your MacBook Pro...

for MacBook Pro 2009-2012

I designed this laptop stand to fit my 15 inch Macbook Pro. I uploaded the .AI file so that you can scale it then use a laser cutter to cut it out. Then assemble. ... I used 1/8 inch MDF for the pieces Feel free to adapt it to your computer and post...

BookLine is a 3d printed stand that makes room for a big monitor by holding your MacBook vertically and keeps it off the desk. Put your MacBook on Bookline, and plug in your external monitor, keyboard, and mouse. I use it at my home office work desk...

It`s a amazing stand for Macbook Primary feature is that the stand does not protrude above the surface of the laptop. With this stand, you can use the laptop keyboard and not beat your hands on the bulging parts of the stand. ...

A stand for Macbook pro 2016/17. ... Tested with my 13" Macbook but a 15" Macbook should work as well.

Remix of - The geometric stand for MacBook Pro Retina - it's just a little flatter

This is a modified version of the Macbook Pro Stand for the new Macbook Pro 2016. ...This is the original thing: http://www.thingiverse.com/thing:1330829 Print Settings Rafts: Yes ...

A simple laptop stand. ...Fits MacBook Pro 16" and Dell Precision laptops, should work with any other laptop that is less than 20mm thick. Print each part 2 times. Assemble by pushing the parts into each other, no glue necessary. ...

Based on idea derived from: Macbook Pro Laptop Stand by jgillick, a rework of Laptop Display Stand (MacBook Pro) by walter (original idea) but designed from scratch in Tinkercad. V2 prints faster and is more economical but v2.1 is more...

It's a vertical stand for MacBooks to use in Clamshell Mode. I use it with a MacBook Pro M1 16" (2021) but other Notebooks up to 20mm thick should work too. It has two additional Compartments for external HDDs or SSDs. both 20mm wider too. They fit...

Based on idea derived from: Macbook Pro Laptop Stand by jgillick, a rework of Laptop Display Stand (MacBook Pro) by walter (original idea) but designed from scratch in Tinkercad. V2 prints faster and is more economical but v2.1 is more...

It's designed to slip into the back of the MacBook Pro 13" & 15" for easy typing and preserving the Apple aesthetic. The cooling stand sits right between the two fan cutouts for maximum effectiveness. The ridge on the top allows the cooling stand to...

You need to print two. ...Made these because i couldn't find proper ones. It fits perfectly my mid 2015 13 inch macbook pro retina. If you are looking for one to use while typing this one might be a bit high. ...So you should print the low version

This is a simple remix from a previous model made by chewbone. ... This adapted version fits nicely the 24 mm thick non-retina MacBook Pro 13" 2012 and 2011, as well as a Lenovo Yoga 15.4".

*Changes (10.01.2021)* - full length dock for better guidance on slip in - 2 delock usb-c adapters for reduced height and a more generic use case - release lever - broader stand-surface *Partlist* - 2x Delock Adapter USB-C Angled...

This is a remix of the stand for the MacBook Pro to fit the 2019 (2 thunderbolt) model.

Minimal vertical stand for my macbook pro 15 to work in clamshell mode. It's supposed to be used on one side so the base has a slight slope. ... It's easy to adapt it to any model.

Remix of [The geometric stand for MacBook Pro Retina](https://www.thingiverse.com/thing:1330829) by [Thmsdc](https://www.thingiverse.com/Thmsdc/about) to fit a Macbook Pro 16-inch from 2019. Tweaked the size of the hook by a few millimetres and...

But from a simple laptop stand, I eventually got to making the HexaHive Stand for MacBook. The HexaHive Stand has the following features: Perfect angle for having the screen at 90 degrees when open. Raises the laptop to a comfortable height which...

I wanted to store my macbook pro vertically while connected to my Akitio Node Pro. ... It requires a 3/8" Carriage Bolt. 8" seems to be perfect for the Akitio Node Pro and the Macbook Pro 13"

Quick and dirty vertical laptop stand I made for my Macbook Pro. The distance from wall to wall is 1", so anything below or near there will fit. Be sure to print two, as the STL only includes one. ...You can also add some furniture pads for extra...

Cast resin into silicone mold Because this my first try at this topic and the original model is not optimised for casting this is not very easy (you have to exercise a combination of caution and violence to remove the models from the moulds). ...However...

This results in a silicone moldCast resin into silicone moldBecause this my first try at this topic and the original model is not optimised for casting this is not very easy (you have to exercise a combination of caution and violence to remove the...