standard 8 film 3d models
508722 3d models found related to standard 8 film.thingiverse
This is a generator for film reels for Super8, standard 8mm, and 16mm film reels. I also included a set of 3 standard sizes for each version as STL files. The reels have 3 insert for the films in the core to make it easy to fit the film onto the...
cults3d
This is a generator for film reels for Super8, standard 8mm, and 16mm film reels. I also included a set of 3 standard sizes for each version as STL files. The reels have 3 insert for the films in the core to make it easy to fit the film onto the...
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
Customized version of https://www.thingiverse.com/thing:1689102 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1689102
thingiverse
standard 8mm film reel shaft (holder), can also be used for magnetic tape reel.
thingiverse
Note that Super 8 film has a different format for image position and sprocket hole size so this is not something you would normally want to do, unless like me you have a Standard 8 film on a Super 8 spool (I guess the original spool broke some time...
thingiverse
Reel to hold a super 8 film. 7" reel for a 1/2" hub Instructions Just print the 2 pieces, Glue them together. ...Watch for the alignment of the keyways.
thingiverse
This is a usable 8 mm film spool. Print the two parts and snap them aligning the three cylinders located near the center of the spool. Use glue to make sure it doesn't separate when turning. ... Print Settings Printer Brand: ...
prusaprinters
... spools. ...Can also be used to transfer film from one spool to another faster than my Eumig 502. But be careful not to tear the film! Connect the tool in you reel, get your electric screwdriver or other fitting tool, and connect it like in my pictures.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: nut_shaft_distance = 1.2 pulley_t_ht = 12 pulley_b_ht = 8 idler = 0 nut_angle = 90 additional_tooth_depth = 0 profile = 6 teeth = 8 retainer = 0...
cults3d
16mm film spools, a centre core to fit most film winders and daylight loaded cameras, 178mm (400ft), 94mm (100ft), 74mm (3", 75ft), and Ilford style 50ft double 8 reels (These have 3 notches on one side and 4 on the other). The 94mm spool will also...
thingiverse
Replacement for Super 8 three inch reels. Print both halves flat side down then glue together. Includes slot for holding film end. ...It helps to put something in the slot while gluing to hold alignment.
myminifactory
(Presupported) Giant Alligator plus standard AlligatorStandard Alligator - 1 piece modelGiant Alligator - 3 Pieces, approx 40 mm height to eyes Standard Alligator - approx 20mm height to eyes
thingiverse
... in the pockets with out a mess or sticking out, I figured I would design one. It has a slide in lid and fits perfectly in the pocket of a Klein's Tool backpack. Husky brand sockets 5/16, 3/8, 7/16, 1/2, 7/16, 5/8, 11/16, 3/4 2 slots for 1/4" bits
thingiverse
This is cine film cutter, for cutting regular double 8 (2x8) or double super 8 (ds8) cine film. Tested with PETG, 16mm film is cutted to 7,94mm and 8,06mm. (0,06mm error) Into two "down" parts you have to put shaving blade (Stainless Steel Double...
thingiverse
6 point standard sockets for 3/8" drive if you like this print check out my youtube channel for many other DIY projects https://www.youtube.com/channel/UCEdB4FizaDt4osd3Lsv_A6Q Thanks!!
sketchfab
Worked on this for the past few months as part of my university work! ...Tried to make it look as much like the original as I could so hopefully you like it! This is the standard kart for Mario, from the game Mario Kart 8/Mario Kart 8 Deluxe
thingiverse
Adapt your GepRC Naked gopro 8 case to any standard Gopro mount. Requires removal of existing mount on the back of the case. (carefully shave off with a sharp knife) Print in TPU at 100% infill. 3 versions included. Checkout our website...
thingiverse
For the single bin pencil holder: The inside is 8" x 2" with an 1/8" wall thickness. (About 203 mm x 51 mm and 3mm wall thickness) The total height is 1.5 inches 3.8cm. The double is the same length and height and about 2 inches wider. ...
thingiverse
... I had some issues so I also made one that was smaller. (toilet bolt 100infill): thread_length = 43 thread_outer_diameter = 8.5 Here were the settings that changed in 3_8in_standardized_bolt.stl: thread_length = 43 thread_outer_diameter = 9.525
thingiverse
I took the dimensions of the Unified Thread Standard and created posts with a pocket for testing different size bolts. PLA is soft enough that you can screw a bolt in with out threading it. The dimensions can be found at...
thingiverse
Developing 8 sheets of 4x5 film at a time. Print with PETCF for best performance. ... PLA is too crunchy PLA+/PETG/ABS are too soft ABS-CF should also work.
cults3d
This is a roller pulley for transporting both 16mm and 8mm film stock. This version has been split in half to eliminate overhangs, while including registration pins for easy assembly. Print two of these for each single roller that you want to make.