stc 1000 temperature controller 3d models

STC-1000 Temperature Controller

This is an enclosure for the STC-1000 AC/Heater controller. You are able to lock the controller inside this box by using the included slide tabs and inserting them in the back of the enclosure and pushing them all the way in with a flat head...

Redesign on your own or use bigger screw that doesn't fit perfectly - it won't be seen anyway.You do not need to use orange clip that comes with STC. I printed with abs and it sits inside nicely without orange clips. You can still use it. ...But you...

Design for a spare retention clip for the STC-1000 temperature controller...

STC-1000 is a nice little temperature controller that can be used to control both a heater and a ventilation in an enclosure. 12V and 220V versions are available for 10-15 EUR (Amazon) or $3-5 (AliExpress).</p> <p>This box is designed to be mounted...

I made a stc-1000 box that prints without supports. I made this for my heated printer enclosure, but there are many uses for these controllers. I hope this fits your needs. The lid is attached to the base via m3 screws with nuts that are inserted...

I made a stc-1000 box that prints without supports. I made this for my heated printer enclosure, but there are many uses for these controllers. I hope this fits your needs. The lid is attached to the base via m3 screws with nuts that are...

This is like original model, it only add a safe power switch for better control as i don't always wan't this to be on or auto on. ...Also i've added holes at bottom case for people who want to use this outside enclosure, like at top and pass the cables...

Enclosure for STC-1000 temperature controller. ... First openscad design, so improvements are welcome.

**Parts list**: (1) STC-1000 temperature controller (readily available online) (1) AC plus socket - (DigiKey part #Q227-ND or equivalent) (1) AC SPST rocker switch - (DigiKey part #EG5676-ND or equivalent) (1) 2.5mm audio jack - (DigiKey part...

as per AJM1's design, i just added on a couple of tabs so I can mount it.

Additional parts list: 1 off STC-1000 temperature controller + sensor 4 off M4x5mm thread inserts (glue in for resin use, heat set where applicable) 4 off M4x25 csk machine screws 2 off C13 clip-in panel mount socket (32.7x25.4mm cutout) 1 off C14...

Its a neat enclosure for an STC-1000 temperature controller available cheap from China on eBay. ...You will need a few other bits and pieces detailed here: http://www.thingiverse.com/thing:717793

Made for the: STC-1000 Temperature controller Standard C14 EU power plug GX12 reverse aviation plugs Check out https://lochte.github.io/posts/Sous_Vide/ for more details. ... Enjoy !

This is a simple bracket for the cheap and popular STC-1000 temperature controller. Designed to mount to 1U of a standard network rack. Allows you to easily use the controller to control rack fans or other devices inside of a rack or enclosure. ...

A case designed to fit an STC/ITC-1000 temperature controller and electrical outlet. Prints support free. Designed with slots to friction fit a Type B electric outlet (decora style). The lid is intended to be held in place with #8 wood...

Its a neat enclosure for an STC-1000 temperature controller available cheap from China on eBay. You will need a few other bits and pieces detailed here:http://www.thingiverse.com/thing:717793 How I Designed This This is prittstift's excellent design...

A case designed to fit an STC/ITC-1000 temperature controller and electrical outlet. Prints support free. Designed with slots to friction fit a Type B electric outlet (decora style). The lid is intended to be held in place with #8 wood screws. I...

STC-1000 temperature module

This enclosure fits a AGPtek STC-1000 digital temperature controller into a Danby refrigerator/ kegerator conversion. It was designed to completely replace the existing enclosure. ... I have included a version with ears which helped to minimize curling...

temperature and humidity controller STC-3028

A basic case for for an STC-1000 (or ITC-1000) temperature controller. Prints without supports, and needs no fasteners. After printing, run the sensor wire out through the back hole of the case and run your power and device wires in through the...

A basic case for for an STC-1000 (or ITC-1000) temperature controller. Prints without supports, and needs no fasteners.</p> <p>After printing, run the sensor wire out through the back hole of the case and run your power and device wires in through...

This is a project box for a Keezer/kegerator controlled by an STC-1000. This specific design uses a fused power socket to provide AC to the controller setup rather than hard-wiring directly . ...BOMSTC 1000IEC 320 C14 - Fused Power SocketWall...

STC-1000 Sondenhalter / STC-1000 Probe holder

This is a sleeve mount for an STC-3018 temperature controller for attachment to the tray stack on a round dehydrator. Use of such a controller may provide more stable temperature management while drying filament or regenerating dessicant. A...

A case for Inkbird ITC-1000 (or ITC-2000): ITC-1000 is a temperature controller used to regulate temperature via a cooling fan into a closed enclosure (based on IKEA LACK) of a 3D printer.

Inkbird temperature controller enclosure that I've lengthened and added feet to so magnets can be used to attach to appliance and make more portable

Amazon search for PID ended up showing the Inkbird ITC-1000 ( which is not a PID, I didn't realize that when i bought it) I liked the 10A contact rating for the internal relay, so i got one and had to figure out how to mount the 'PID' controller. I...