stepper driver cooler 3d models

This bracket was custom-designed by me for my CTC i3 printer, which had been skipping steps and I discovered that the issue was caused by overheating TMC2100 drivers cutting out. If you have a standard GT2560 board installed, this is a great solution...

Hello. I am a novice in design, I do it for hobby purposes. I know that stepper motors can work at high temperatures, but why not keep it cool in a cheap and simple way?I designed it in a way suitable for 40*40*10 mm fans to stand behind the x and y...

The Leadshine MX3660 is a cutting-edge, 3-axis digital stepper drive featuring DSP technology. Designed for seamless control of up to three 2-phase (1.8°) motors in NEMA 17, 23, 24, and 34 frame sizes, it boasts a wide input voltage range of 20-60VDC...

This component serves to effectively chill the UP Mini Stepper's, specifically designed to accommodate a 50mm fan that optimizes cooling for the motor when printing with PLA filament. ...The precise spacing between the holes is set at 40 millimeters.

This installation needs a stepper damper (or a 6mm spacer), as there is end-switch connector in the way otherwise. I used Noctua 4020 fan (5.5CFM compared to 7CFM of the original fan), but it would fit (probably) any 40mm fan, no thicker than 20mm...

my bottom stepper motors really got quite hot: roughly around 60°C - and that shouldn't normally be a problem, but to get the most power possible out of my Nema stepper, i came up with this clever little fan mount. prints in a snap without any...

Hey Since the stepper motor of the Y-axis is always so extremely hot, I designed a bracket for the motor to cool it better and to keep the temperature low. I used a 4020 Sunon fan, any other 4020 fan works too. ... In order to get a better stability I...

Simplified, but modeled using calipers to ensure accurate dimensions.

I designed a new cooler for the Sidewinder X1 that takes in a standard 40x40 fan. ... I used this one here:...

Simplified, but modeled using calipers to ensure accurate dimensions. The connector pitch is 0.156" (3.96mm). ...{​Terminal connectors are not 100% accurate yet.}​Model units are inch.

So I found that in the Taiwan summers, with my room getting upwards of 35 celsius, the Z axis motor of my Ender 3v2 heats the all metal stepper gear above it so much that it softens the filament passing through, squishing it and causing the gears to...

**Edit - after giving this a test run, the Y stepper motor is dead cold to the touch, it appears it doesn't even need cooling veins to efficiently cool the motor. ...Might revisit in the future and lower the shroud to speed up airflow along the top...

29.07.2019 Update V4 I uploaded a newer version, featuring tighter fitment around the stepper motor, improved airflow, and enhanced wiring. Printing without support in ABS or PETG is now possible. If you're using ABS, print the securing bolt...

Here's the modified model split to print without supports, making it easier for anyone who dislikes supports as much as I do.

Simplified, but modeled using calipers to ensure accurate dimensions. The threads in the heat sink are M4 x 0.7 mm and the connector pitch is 0.156" (3.96mm). ...{​Terminal connectors are not 100% accurate yet.}​Model units are inch.

Simplified, but modeled using calipers to ensure accurate dimensions. The threads in the heat sink are M4 x 0.7 mm and the connector pitch is 0.156" (3.96mm). ...{​Terminal connectors are not 100% accurate yet.}​Model units are inch.

Simplified, but modeled using calipers to ensure accurate dimensions. The threads in the heat sink are M4 x 0.7 mm and the connector pitch is 0.156" (3.96mm). ...{​Terminal connectors are not 100% accurate yet.}​Model units are inch.

Improve your Nema stepper motor's temperature with this fan print! Designed for 42x42mm motors and using a standard 60mm fan, support material is not required. Attach the fan with wooden screws or double-sided tape, then mount it onto the motor using...

In fact, a very well-calibrated 3D printer is necessary to get them right, particularly the Phillips and slotted tips, which are quite thin. The layer height must be no higher than 0.10mm; any higher values will not produce satisfactory results. You...

Update hint!!! After replacing the heatbreak with an original e3D, we were able to print the material that never ran before. most PLA filaments works very well (many times printed over 20h at 29°C ambient temperature) I use a empabst fan instead of...

Original designer/creator/inspiration: CG-Tech https://www.thingiverse.com/thing:2975582 MK3S & MMU2S Models: jzkmath https://www.thingiverse.com/thing:3434917 https://www.thingiverse.com/thing:3467092 Background: CG-Tech had the initial concept of...

Simple Anycubic i3 Mega S fan duct for stepper driver upgrade to TMC2208 with use of standard 50x50mm cooler.

Humans use 3D coolers filled with ice to keep perishable items at a safe temperature. ...The top, handles, and body of these coolers work together seamlessly, yet remain separate entities.

Stepper Motor 3D Model for Arduino Base model : 5V Stepper Motor 28BYJ-48

This 3D model showcases a beer cooler, designed using Rhino 5 software. ...The final render was created with KeyShot 5 for an accurate representation of the design.

** Waret cooler**

Camping cooler

Precise 3D rendering requires an authentic water cooler model with meticulous detail, perfect for high-definition renderings up close. ... Formats available include: 3DS Max 2013 V-Ray 3.40.03 FBX 2006 OBJ format Detailed textures included for...

The set includes 2 cooler models: Ecotronic H1-LN Ecotronic H1-T

A CPU-Cooler with 2 different plates, 10 tubes and caps.