stepper motor generator 3d models

Build Mod Hack 5mm to 8mm Tall CouplerThis is intended to fit a 5mm shaft of a stepper motor that has a D shaft and a 8mm lead screwDimensions:D = 20mmH = 37.5mmPrinting:Nozzle 0.4mmLayer   0.2mmInfill     35% Min.Hardware:Screws...

The Printrbot filament guide and fan mount are essential for a warm extruder stepper motor. I recommend using this 4cm fan from Dealextreme (http://www.dealextreme.com/p/cooling-fan-for-vga-video-display-card-4cm-4cm-15564) for optimal cooling. Drill...

Time will tell if PLA was the right material because the stepper motors can get hot and the mount might get weaker and looser. Excuse the messy cables. I'm still looking for a suitable cooling solution and that is the current setup to test...

Build Mod Hack 5mm to 8mm CouplerThis is intended to fit a 5mm shaft of a stepper motorthat has a D shaft and a 8mm lead screwDimensions:D = 20mmH = 25mmPrinting:Nozzle 0.4mmLayer   0.2mmInfill 35% Min.Hardware:Screws:  2 - 3mm x 14 Hex...

To make it compatible with Anycubic i3/mega printers that have stepper motor driver fan ducting, I rotated the mounts 90 degrees to save precious space. It was a challenge, but the end result is well worth it! I printed this design on my trusty...

I've used the versatile unipolar 28BYJ-48 stepper motor in numerous projects due to its affordability and widespread availability from online retailers like Amazon or Ebay. Although its torque is relatively weak, it can be substantially increased...

This model enables mounting a stepper motor damper on the X axis, provided the motor features a press-fit pulley that cannot be removed without risking damage to the motor. Printing a simple stop flag or a mount for an M18 sensor becomes possible,...

I had some overtemperature problem with my stepper motors (shutdown during operation), so I decided to implement additional cooling for them. The part has a little shield to protect the workpiece from as much airflow as possible. The holder is made...

Logitech C270 cam mount for Stepper Motor (compatible with Sidewinder X1) 2 M3 nuts and 3 M3 cap head bolts are required. To mount the Webcam, you have to take off the standard stand. To do this, remove the elastic cover on one of the sides of the...

This is my slowly and gradualy desgined cable chain for my beloved Ender 5 with Micro Swiss Direct Drive.thIt is a remix of very sturdy chain for Ender 3 by Diogo Santos https://www.thingiverse.com/thing:3715002and some Nema17 motor chain mount I...

Logitech C270 cam mount for Stepper Motor (compatible with Sidewinder X1) 2 M3 nuts and 3 M3 cap head bolts are required. To mount the Webcam, you have to take off the standard stand. To do this, remove the elastic cover on one of the sides of the...

The 28BYJ-48 stepper motors are slow, but very cheap and come with their own controllers, which eliminates the need to purchase a motor controller for the SMARS bot entirely. 3D printing the screws makes this robot more accessible for STEM programs...

Stackable 4:1 Planetary Gearbox for the 28BYJ-48 Stepper Motor (Remix) Preface: I needed a planetary gear box for my project using 28BYJ-48 Stepper Motor because i needed more torque, but DL_3D's version was a little bit to big for my project. So...

I had some troubles getting the servo to work with Marlin firmware, so I made a couple of other mounts to use a nema17 pancake stepper & a 28BYJ-48 stepper motor. I then found a way to use the servo with klipper firmware, but might use a stepper...

I created these after installing stepper motor dampeners and discovering how hot the motors were getting without frame contact. Using Noctua fans with their rubber mounting system keeps them cooler, almost silent, and won't be heard over the hot end...

... and was forced to hang the bracket from the extruder via a zip tie until I came up with this solution. This is a remix of the original part that broke that I have reinforced and a bracket for holding a 40mm fan on the bottom of a stepper motor.

Thanks to phili76 for original design (and big ups for providing STEP files), unfortunately center hole for some of the steppers I have here were little too tight. I've simply increased centre hole (by 2mm in diameter) to 24mm to accommodate these...

Made these in Fusion 360 as I needed to figure out which stepper motor and endstop was which on my DIY printer while tidying up the wiring. Print at whatever layer height you prefer (I chose 0.2 since they're purely functional). I printed them with...

I design this X-STEPPER MOTOR COVER FOR LINEAR RAIL.It has 4mm holes and 1 on the top 3mm for cable chain mount or endstop wire.I stretched the length and I enlarged the width of the holes so that the pins go through without struggling to screw or...

... I had a problem with the motors heating up and warping the motor covers, and I wished I had access to the eccentric nuts to adjust the V Wheels without taking the cover off, so I remade the enclosures too, with holes for ventilation and nut access.

I encountered some issues getting the servo to work with Marlin firmware, so I created a few other mounts using a Nema17 pancake stepper and a 28BYJ-48 stepper motor. Then I found a way to use the servo with klipper firmware, but I might switch to a...

[This mount](https://www.thingiverse.com/thing:4752465) by [rucker](https://www.thingiverse.com/rucker) had a notch cut out in case I decide to add stepper motor dampers or remove my glass bed later on. All I did was take the two mounts, slice...

The Ender 5 y-axis though has a dual axis motor making the regular setup unusable. Kwyman made an excellent simple mounting plate that allows compatibility. I combined his design with a cover I designed for the s42b's mini lcd display (based on a...

With my design tightening on both sides at once, it engages more teeth on the pulleys of the lead screws, making it possible to run on a single z-axis stepper motor. 3. A tension adjustment knob is included for precise adjustments as needed. After...

made a way to connect it with an M3 nut and bolt to the stepper Category: Tools

So i researched for a probable solution online and found out that i can get rid of default z stepper brackets with using alternative brackets that attach to backside of stepper motor. However solutions on thingiverse was for other machines. So i...

Electronics; Arduino Nano (clone -I used an Elegoo module) 28byj-48 stepper motor and ULN2003 module, for motor speed control 10K potentiometer USB type B module (as for my son, I thought this would be more sturdy and less prone to fall out) Wago...

First, make sure you use PETG so that the plastic doesn't soften due to the stepper motor heat. Next, attach neodymium magnets to the visualiser using superglue, roughing up the mating faces with sandpaper first. I recommend using 8mm x 3mm...

As a proud and patriotic Scotsman, I thought I'd fly the flag for my country whilst 3D printing! Make sure that you use PETG so that the plastic doesn't soften due to the stepper motor heat. Use superglue to stick neodymium magnets to the visualiser,...

Printing 75A TPE:https://youtu.be/MNSuiiIl1QoPrinting eSUN TPE83A with this upgrade.https://youtu.be/S0R_FAOXQnI10/22/2023 :My updated design of this mount has no loss of X Axis printable area, but you need a 8$ 42-23mm stepper,updated...