strengthened filament guide for iroberti s um2 feeder 3d models

Update 2014-07-29: I've re-designed parts of the feeder to get rid of a few parts that were causing people problems and also to strengthen it slightly.Right, here's my second (public) attempt at a new feeder design for the UM2. My goals were:- Able...

... ...To function properly, you'll need to select one of the three available wheels. It's advisable to print all components with a 20% infill rate, except for the bolt which should have a significantly higher density (50% or more) to ensure stability.

I'm preparing to print and my filament is sitting on top of a wooden box, which is why I created this guide.

... version). ...His original design had a rather thin base, which resulted in warping near the screw slots when the filament encountered minor resistance due to stress. ...To address this issue, I thickened the base to make it significantly sturdier.

This is a reworked version of "Beautiful Mini Filament Keychain" by Heliox, where I've reinforced pieces one and three to prevent them from cracking.

<p>Tired of finding the hole you can't see when the bed is in the way? ...You want this. It's not pretty, but it's dead on and works.

... If it doesn't fit, try different values ​​of flow or horizontal expansion. Only two 3mm screws, nuts and washers (optional, but recommended )of the same size are necessary for assembly. ... Thanks to Christian Schiffer for original design

I made this after moving my Filament Spools to the top of the Printer to give me More space to either side of the printer. ... The filament was cutting into the filament sensors. ... This design fits beneath the Sensors, between the sensor and Printer.

I made this after moving my Filament Spools to the top of the Printer to give me More space to either side of the printer. The filament was cutting into the filament sensors. ...This design fits beneath the Sensors, between the sensor and Printer.

My goals were to be able to release the filament for quick and easy change between filaments, reuse original parts from the old feeder, minimize friction, and supply additional guidance for flexible filaments (untested at this point and optional to...

This is a custom adapter for IRobertI's low friction spool holder, specifically designed to fit the UMO 3D printer. To get the best results, it's recommended to use at least 30% infill and 0.8mm walls when printing the adapter. For those interested...

The Filament Feeder is compatible with all aluminum frames used in the ZONESTAR 3D printer series, including models such as the D805 (Z5), D806 (Z6), D808 (Z8), and Z9 and Z10. ...This feeder supports 1KG filament rolls for efficient 3D printing.

Huge thanks are owed to them for their fantastic work!!!https://www.youmagine.com/designs/alternative-um2-feeder-version-twohttps://www.youmagine.com/designs/extruder-um2-version-2Special appreciation goes out to Ultimaker for publishing the STEP...

I finally found this object https://www.thingiverse.com/thing:3550741 but it wasn't suitable for my printer model, a Monoprice Maker Select Plus, so I decided to start a project on Tinkercad and, inspired by the aforementioned object and starting...

... the build platform. Use 20% infill, 2 shells, and a .20mm layer height when printing. For permanent installation, apply glue between the filament guide and the clip's stubby legs; otherwise, the filament may dislodge the part from your printer.

I struggled to get the lower PTFE guides on elporcho's filament feeder working properly on my machine, but fortunately, I was able to swap them out for a sturdier tube. ...Elporcho's design is excellent, and his spool holder is just as well thought out!

This guide focuses on 3mm filament usage with Wade's/Gregs Extruder, which is a modified version of profbraino's. Key improvements include an enclosed, tapered filament hole and a clean mesh for optimal performance. ...Happy printing!

I finally found this object https://www.thingiverse.com/thing:3550741 but it wasn't suitable for my printer model, a Monoprice Maker Select Plus, so I decided to start a project on Tinkercad and, inspired by the aforementioned object and starting...

... the filament guide to the printer's body. ...To install it, print on a 3D printer (e.g., UP!), remove the bolt from its location near the top of the filament guide, pass the bolt through the new clamp and reinsert it into the original hole in the case.

To achieve this, I attached a pneumatic connector for testing purposes; however, I advise against replicating this setup as the filament tends to jam inside the tube. ... Print Settings: Printer: Trinus 3D Rafts: None Supports: None Resolution: 0.15 mm...

Ben Jackson's Top Guide proved indispensable for my Accessible Wade's Extruder as it prevented the filament from falling off the hobbed bolt when tugged to the side. The Top Guide ensures that the incoming filament remains vertically centered above...

To this end, I attached a pneumatic connector for testing purposes; however, I strongly advise against replicating this setup as it can lead to issues with the filament's movement within the tube. ... Print Settings Printer: Trinus 3D Rafts: Disabled...

Filament guide for Creality 3D CR-10 for top roll holder. Made the guide out of PLA and used Ultimaker Cura  on recommended settings Profiles 0.16, infill 40% and support. ... Material needed: 1x bearing 608-2z, 1x hex bolt M8x20, 1x hex nut M8,...

This model allows the filament to be guided around the roller to ensure a well-aligned entry.

Filament guideSuitable for Original Prusa i3 MK3 / S+Suitable for Filament spool holder without bearings&nbsp;Print these parts / quantitiesPart 1 = 1 pieceFilamentführerGeeignet für Original Prusa i3 MK3 / S+Passend zu Filament spool holder without...

To remedy it, I created a compatible filament guide for the aluminum extruder mod. After installation, no more skipped steps! I have only tested the guide on my Replicator 1 Dual (MK7 extruders), and it may not fit MK8+ extruders. Print guides using...

I saw tons of filament guides for the CR-10, longs, shorts, with PTFE, with angle, no angle, red, white, blue, etc.... But finally, this simple cylinder of PLA works really great. Printing time < 10 minutes Length of filament: 225mm (yes mm !) So...

This laser-cut MDF guide for 3mm filament is an adapted version of Sacha Di'Angeli's PS1 design and Thing 13351. It features a slot that enables easy access for changing filament and cleaning the hobbed bolt by flipping up. The OpenSCAD file, created...

... part and attach it using snap pegs in the two top rectangular holes. Although it might wiggle slightly, it will still function properly. For a tighter fit, use a damp paper towel on the holes before pressing the filament guide into place.

This is a custom modification of MegaMarkey's remix of the end clip, specifically designed for use with Filboyt's filament guide. It's ideal for printers with high tolerances, and can be used as an alternative if other clips don't fit properly. The...